Idiomas disponibles
Idiomas disponibles
Provide Adequate Gas Supply
Your range is designed
to operate
at a pressure
of
4" (10.2
cm) of water
column
on natural
gas or, if
designed
for LP gas (propane
or butane),
10" (25.4
cm) of water column,
Make sure you are supplying
your
range
with
the
type
of gas
for which
it is
designed.
This range is convertible
for use on natural
or propane
gas, if you decide
to use this range on a
different
type of gas, conversion
adjustments
must be
made by a service technician orother
qualified
person
before attempting
to operate
the range on that gas.
For proper operation,
the pressure of natural gas sup-
plied to the regulator
must be between
4" (10.2 cm)
and 13" (33 cm) of water
column.
For LP gas, the
pressure
supplied
must be between
!0" (25.4 cm) and
13" (33 cm) of water column.
When checking
for prop-
er operation
of the regulator,
the inlet pressure
must
be at least
1" (2.5 cm) greater
than
the operating
(manifold)
pressure
as given
above.
The
pressure
regulator
located
at the inlet of the range
manifold
must remain
in the supply line regardless
of whether
natural or LP gas is being used. A flexible metal appli-
ance connector
used to connect
the range to the gas
supply
line should
have an I.D. of 1/2" and be 5 feet
(1.5 m) in length
for ease of installation.
In Canada,
flexible connectors
must be single wall metal connec-
tors no longer than 6 feet (1.8 m) in length.
2
Connect the Range to Gas
Shut off the main gas supply valve before disconnect-
ing the old range and leave
it off until new hook-up
has
been
completed.
Don't
forget
to
relight
the
pilot on other gas appliances
when you turn the gas
back on.
Because hard piping restricts
movement
of the range,
the use of an A.G.A.-certified
flexible metal appliance
connector
is recommended
unless local codes require
a hard-piped
connection.
Never use an old connector
when installing
a new range. If the hard piping method
is used, you must carefully
align the pipe; the range
cannot be moved after the connection
is made.
To prevent
gas leaks, put pipe joint compound
on, or
wrap
pipe thread
tape with Teflon*
around
all male
(external)
pipe threads.
*Teflon: Registered trademark of DuPont
(continued next page)
Gas Pipe and Electric Outlet Locations for
Models Equipped
with Seat_edBurners
This area allows
for flush range
30"
installation with
(76.2 cm)
through-the-wall
,
_i"
,
,
connection of pipe
I .- f
I
i_
stub/shut-off
t_4 "
IF
.4
valve and rear wall
I (10.2
Ijl I
nl
t20V outlet.
I cm)
,,._1_
122 eoo F
.
2"
I_%_: ..... I
. (s.1era)
(10.2
"
flush range installation
l
with through4he41oor
I
connection of pipe
I
stub/shut-off valve,
I M
¢
Gas Pipe and Electric OutBet Locations for
Models Equipped with IDuam Burners
3(} 'r
(76.2 cm)
(17.8
om
i
Shortest
connection
from hard pipe
stub location
to range
hoo _up
This area allows
for flush range
installation with
through-the-
wall connection
of pipe
stublshut-off
valve and rear
wall 120V outlet.
\
g_
(22.9 cm)
2½"
'(6.4 cm)
This area allows
for flush range
installation with
through-the-floor
connection of pipe
stub/shut-off valve.
29
