Idiomas disponibles
Idiomas disponibles
FIG. 1
STRAIGHT UP
TOUT DROIT
HACIA ARRIBA
FIG. 2
K
A
J
H
G
LOOSEN
BLADE DIRECTION
DESSERRER
DIRECTION DE LA LAME
AFLOJE
DIRECOION
DE LA HOJA
FIG 4
F1
F2
FIG. 5
FIG. 3
BLADE DIRECTION
DIRECfION DE LA I..AME
DIRECCION DE LA HOJA
POSITION OF TEETH ON LEFT SIDE OF MACHINE
POSITION DES DENTS SUR LE COI"F!!!
GAUCHE DE LA MACHINE
POSICION DE LOS DIENTES EN EL LADO IZQUIERDO
DE LA MAQUINA
FIG. 6
Blade
Selection
In general, first consider the size and shape of the work, and the type of material to be cut.
Remember, for the most efficient cutting, the coarsest tooth blade possible should be used in a
given application, because the coarser the tooth, the faster the cut. In selecting the appropriate
number of teeth per inch of the band saw blade, at least two teeth should contact the work
surface when the blade is rested against the workpiece. As a rule of thumb, soft materials
usually require coarse tooth blades, while hard materials require fine tooth blades. Where a
smoother finish is important, select one of the finer tooth blades.
Select the appropriate band saw blade according to the material type, dimensions, and number
of teeth. See Blade Description chart.
The following table is intended as a general guide only. Determine the type of material and
dimension of the workpiece and select the most appropriate band saw blade.
_CAUTION:
Never use the band saw to cut resin materials which are subject to melting,
Melting of resin material caused by high heat generated during cutting may cause the band saw
blade to become bound to the material, possibly resulting in overload and bum-out of the motor.
Type of band saw blade
Number of teeth
Workpiece thickness
1/8" (3.2 mm) and under
1/8" - 1/4" (3.2 mm - 6.4 mm)
1/4" - 13/32" (6.4 mm - 10.3 mm)
13/32" (10.3 mm) and over
Blade
Speed
BLADE DESCRIPTION
Bi-Metal
24
18
14
10
14/18
10/14
Your DWM120 portable band saw is equipped with variable speed for greater versatility.
Turn the speed wheel (I) to select the desired speed (Fig. 1). Speed 1 is the slowest speed;
Speed 5 is the fastest. Use speed settings 1-5 when connected to an AC power supply.
When cutting copper, brass, bronze, aluminum, cast iron, angle iron, and mild steel, use a higher
speed.
When cutting plastic pipe, tougher steels, chrome steel, tungsten steel, stainless steel, and other
problem materials, use low speed.
NOTE: When cutting plastic pipe, higher speeds may melt plastic.
Blade
Tracking
Your band saw is equipped with an adjustable blade tracking mechanism which assures
proper blade tracking at all times. The back edge of a properly aligned blade will run
lightly against one or both of the back up rollers in the blade guides. (The pressure between
the edge of the blade and the roller will be very slight and will not damage either the blade or
the roller.)
TO ADJUST THE BLADE TRACKING
1. Use a 1/2" (13 mm) wrench to loosen the adjustment locking nut (G), shown in Figure 1 by
turning it one or two turns counterclockwise.
2. Use a screwdriver to turn the tracking screw 1/4 turn. Turning the screw clockwise will move
the blade up toward the blade guide rollers. Turning the screw counterclockwise will move
the blade down away from the rollers.
3. Adjust so that the back edge of the blade lightly touches the rollers then securely tighten the
locking nut. (It will be necessary to plug the saw in and run it to observe the tracking.)
4. Observe blade tracking between runs and repeat Steps 1-4 as necessary to achieve proper
blade tracking.
Removing
and Installing
Blades
ACAUTION:
Cut Hazard. Blade tension lever is under spring pressure, Maintain control of
lever when releasing blade tension,
TO REMOVE BLADE (FIG. 1, 2)
1. Rotate the blade tension lever (H) clockwise until it stops to release tension in blade.
2. Turn the saw over and place it on a workbench or table with the cord to the left.
3. Begin removing the blade at the blade guard (M) and continue around the pulleys (L). When
removing the blade, tension may be released and the blade may spring free. SAW BLADES
ARE SHARR USE CARE IN HANDLING THEM.
4. Inspect the guide rollers (F1, F2) and remove any large chips which may be lodged in them.
Lodged chips can prevent rotation of the guide rollers and cause flat spots on the guide
rollers.
5. Rubber tires (N) are mounted on the pulleys (L). The rubber tires should be inspected for
looseness or damage when changing the blade. Wipe any chips from the rubber tires on the
pulleys. This will extend tire life and keep the blade from slipping. Ifany looseness or damage
occurs, the tool should be brought to an authorized DEWALT service center for repair or
replacement as soon as possible. Continued use of the tool with loose or damaged rubber
tires will cause unstable travel of the band saw blade.
TO INSTALL BLADE (FIG. 1, 3-5)
1. Position the blade so that the teeth are on the bottom and angled toward the work stop, as
shown in Figures 1 and 3.
2. Slip the blade into the guide rollers, as shown in Figure 4.
3. Holding the blade in the guide rollers, place it around both pulleys (L) and through the work
stop (E), as shown in Figure 5.
4. Make sure that the blade is fully inserted into the guide rollers and positioned squarely
against the rubber tires.
5. Rotate the blade tension lever (H) counterclockwise until it stops and then gently turn the
saw over so that the pulleys rest on your work bench or table and. Make sure the teeth face
away from the bandsaw (Fig. 1,3).
6. Turn the speed wheel to low speed (1) and then turn the saw on and off a few times to
ensure that the blade is seated properly.
Multi-position
Bail Handle
(Fig.
1)
A bail handle is provided for carrying the tool and for use as an additional handle. Assemble the
bail handle in one of the milti-positions (forward, 45 ° or straight up) shown in Figure 1. When
adjusting the bail handle from one position to the other, loosen the bail handle knob and move
the handle to one of the three positions and tighten knob.
FIG. 7
RECOMMENDED
cu'rI'ING
POSITIONS / POSITIONS
DE COUPE
RECOMMAND#ES
/ POSICIONES DE CORTE RECOMENDADAS
YES / OUI / S/
NO / NON / NO
YES / OUl / Si
NO / NON / NO
YES / OUI / Si
YES / OUI / Si
NO / NON / NO
NO / NON / NO
YES / OUI / S[
YES / OUI / S[
NO / NON / NO
NO / NON / NO
Item
Model
DWM120
Motor
Type
Protected type, series commutator motor
Power source
single-phase, AC 60Hz
Voltage
120 volts
Full-load current
10 amp
Band Saw
Dimensions
1/2" x 44-7/8" x .020"
Blade
(12.5 mm x 1140 mm x .5 mm)
Peripheral speed
100 - 350 ft/min (30 - 106 m/min)
Max. Cutting Pipe outer dimensions
4-3/4" (120.7 mm)
Dimensions
Stock
5" x 4-3/4" (127 mm x 120.7 mm)
Net Weight
15 Ibs. (6.8 kg)
Cord
3 conductor type captive cable 8.0 ft. (2.4 m)
Article
ModUle
DWM120
Moteur
Type
Type prote,qe, serie moteur a,collecteur
Source de courant
monophase, CA 60Hz
Tension
120 volts
Courant de pleine
10 amp
charqe
Dimensions
Lame de
scie a ruban
Vitesse peripherique
Longueurs
Dimensions externes
max. de
de tuyau
coupe
Bois speciaux
Poids net
Cordon
12,5 mm x 1140 mm x 0,5 mm
(1/2 pox 44-7/8 pox 0,020 po)
30 - 106 m/min (100 - 350 pi/min)
120.7 mm (4-3/4 po)
127 mm x 120.7 mm (5 po x 4-3/4 po)
6,8 k,q (15 Ib)
Cordon a,3 broches et 3 conducteurs
de 2,4 m (8 pi)
Articulo
Motor
Hoja de la
Sierra de
Banda
Max.
Dimensiones
de Corte
Peso Neto
Cable
Modelo
Tipo
AlimentaciOn Electrica
Voltaje
Corriente a carga
completa
Dimensiones
Velocidad periferica
Dimensiones externas
de tuberia
Reserva
DWM120
Tipo prote,qido, serie de motor commutador
Corriente alterna de 60Hz, monof6,sica
120 voltios
10 amperios
12.5 mm x 1140 mm x .5 mm
(1/2 pulg. x 44-7/8 pulg. x .020 pulg.)
30 - 106 m/min (100 - 350 pie/min)
120.7 mm (4-3/4 pulg.)
127 mm x 120.7 mm (5 pulg. x 4-3/4 pulg.)
6,8 kg (15 Ibs)
3 Cables tipo cautivos conductores
de 2,4 m (8,0 pie)
Work Stop Adjustment
To support large workpieces, the work stop should be lowered following these steps:
1. Loosen the two screws (R), shown in Figure 1, with the hex wrench provided.
2. Move the work stop (E) to the desired position (Fig 5).
3. Securely tighten screws (R).
