Tunturi T40 Manual Del Usuario página 21

Cleaning and maintenance
⚠ WARNING
• Beore cleaning and maintenance, remove the mains plug rom
the wall socket.
• Do not use solvents to clean the equipment.
- Do not block the ventilation openings. Keep the ventilation
openings clear rom dust, dirt and other obstructions.
- Clean the equipment with a sot, absorbent cloth ater each use.
- Clean the visible parts o the equipment with a vacuum cleaner
with a small suction nozzle
- Regularly check that all screws and nuts are tight.
Belt and Running Deck
Your treadmill uses a very high-eicient low-riction bed. Perormance
is maximized when the running deck is kept as clean as possible.
Use a sot, damp cloth or paper towel to wipe the edge o the belt
and the area between the belt edge and rame. Also reach as ar
as practical directly under the belt edge. This should be done once
a month to extend belt and running deck lie. Use water only - no
cleaners or abrasives. A mild soap and water solution along with a
nylon scrub brush will clean the top o the textured belt. Allow the
belt to dry beore using.
Lubrication (ig. F-4)
The running belt must be checked or lubrication condition regularly.
Thereore the treadmill comes with a 300 hours reminder unction.
The "TIME WINDOW" will display "OIL" and will make an acoustic
beeping sound every 10 seconds to remind you. Follow the below
checking procedure and eliminate the "OIL" message and acoustic
warning signal by pressing and hold the "STOP" button or at least 3
seconds during this warning signal.
⚠ WARNING
• Beore lubrication, remove the mains plug rom the wall socket.
⚠ CAUTION
• We recommend to check the running belt lubrication at least
once every month, as more actors than time can be eective to
the lubricant conditions.
• Only lubricate the running belt i necessary. I you apply too
much lubricant, the running belt will slip easily due to lack o
friction.
- Stand steadily on the running belt.
- Take hold o the ront handlebar and push the running belt with
your eet so that it slides back and orth. The running belt must
move smoothly and evenly without making sound.
- I the running belt does not move smoothly and evenly or i the
running belt does not move at all, touch the underside o the
running belt with your ingertips to check the lubrication:
• I you eel lubrication or your ingertips are shiny, there is
suicient lubrication on the running belt.
• I you do not eel lubrication or your ingertips are dusty or
rough, apply lubricant (15-20 ml) in the middle o the running
deck under the running belt and let the equipment operate at
5km/h or at least 5 minutes.
• Ater lubrication, do not old the equipment beore having done
a workout or 20 minutes with a speed o at least 5 km/h. The
lubricant will be spread evenly over the running belt.
Belt Dust
This occurs during normal break-in or until the belt stabilizes. Wiping
excess o with a damp cloth will minimize build-up.
General Cleaning
Dirt, dust, and pet hair can block air inlets and accumulate on the
running belt. On a monthly basis: vacuum underneath your treadmill
to prevent buildup. Twice a year, you should remove the black motor
hood and vacuum out dirt that may accumulate.
UNPLUG POWER CORD BEFORE THIS TASK.
Belt adjustments
Adjustment must be made rom the rear roller. The adjustment bolts
are located at the end o the step rails in the end caps.
- Tighten the rear roller bolts (clockwise) only enough to prevent
slippage at the ront roller. Turn both running belt tension
adjustment bolts in increments o 1/4 turn each and inspect or
proper tension by walking on the belt at a low speed, making sure
the belt does not slip. Keep tensioning the bolts until the belt
stops slipping.
- I you eel the belt is tight enough, but it still slips, the problem
may be a loose Motor drive belt under the ront cover.
- Do Not Over-tighten
Over tightening will cause belt damage and premature bearing
failure.
Running belt tracking adjustment
The perormance o your treadmill is dependent on the rame running
on a reasonably level surace. I the rame is not level, the ront and
back roller cannot run parallel, and constant belt adjustment may be
necessary.
The treadmill is designed to keep the running belt reasonably
centered while in use. It is normal or some belts to drit near one
side while the belt is running with no one on it. Ater a ew minutes
o use, the running belt should have a tendency to center itsel. I,
during use, the belt continues to move toward one side, adjustments
are necessary.
EXCEPTION:
During rehabilitation where the user is using one leg much stronger
than the other, it might happen that the running belt drits to one
side. In these cases you should not adjust unless the running belt
does not centre itsel during normal condition usage.
To set running belt tracking (ig. F-5)
A 10 mm Allen wrench is provided to adjust the rear roller. Make
tracking adjustments rom the let side only. Set belt speed at
approximately 3 to 5 kph.
Remember, a small adjustment can make a dramatic dierence!
Turn the bolt clockwise to move the belt to the right.
Counterclockwise to move to the let. Turn the bolt only a 1/4 turn
and wait a ew minutes or the belt to adjust itsel. Continue to make
1/4 rotation turns until the belt stabilizes in the center o the running
deck.
The belt may require periodic tracking adjustment depending on use
and walking/running characteristics. Some users will aect tracking
dierently. Expect to make adjustments as required to center the
tread-belt. Adjustments will become less o a maintenance concern
as the belt is used. Proper belt tracking is an owner responsibility
common with all treadmills.
‼ NOTE
• Damage to the running belt because o incorrect running-belt
adjustments is not covered by the products warranty.
Troubleshooting
Despite continuous quality control, deects and malunctions caused
by individual components may occur in the equipment. In most cases
it's unnecessary to take the whole device in or repair, as it's usually
suicient to replace the deective part.
I the equipment does not unction properly during use, contact your
Tunturi dealer immediately. Always give the model and serial number
o your equipment. Please state also the nature o the problem,
conditions o use and purchase date.
2 1
English