Idiomas disponibles
Idiomas disponibles
EN
PRODUCT DESCRIPTION
1 Charging station
2 Inbuilt ToF sensor
3 Front laser sensors
4 Bumper
5 Cleaning on/off button
6 Side vertical sensor
7 Side brush
8 Cliff sensors
9 Charging electrodes
10 Front wheel
11 Rotation brush
12 Rotation brush guard
13 Dirt extraction orifice
14 Water dosage orifices
15 Side wheel
LIST OF PARTS
A. Dust container
B. Water container
C. Mopping module
D. Mopping pad
E. Dust bag
F. Combi filter
G. Universal rotation brush
H. Rotation brush for hard floors
I. Side brush
J. Cleaning brush
K. Power supply cable
DESCRIPTION OF THE CHARGING STATION
1.1 Lift-up lid
1.2 LED indicator
1.3 Infra-red sensor
1.4 Charging electrodes
1.5 Dirt suction orifice
1.6 Base
MOPPING MODULE
1.A Water tank
1.B Water tank unlocking button
1.C Water filling orifice
1.D Guide
1.E Cleaning pad
1.F Mopping module
1.G Mopping module unlocking button
68
16 Dust container
17 Wi-Fi indicator
18 RESET button
19 Dust container unlocking button
20 Mop module unlocking button (1/2)
21 Water tank unlocking button
22 Cleaning brush
23 Dust container
24 Dirt suction orifice
25 Dirt extraction orifice
26 Air exhaust
27 Filter
28 HEPA Filter
29 Foam filter
30 Unlocking button (dirt disposal from the dust container)
VR3550
KEY FEATURES
Cleaning / ON/OFF
• Press the button and hold it for 3 seconds to switch
on/off the robot vacuum (the device cannot be
switched off during the charging process)
• Press the button to start/interrupt the cleaning.
Charging / Local cleaning
• Press briefly to start or pause charging.
• Long press to start local cleaning.
• If the robot vacuum is in the charging base, short
press the button to start dirt extraction from the
device
Circular LED indicator
• White: Operation mode, battery capacity ≥ 20%
• Yellow: Low battery capacity < 20%
• Red: Robot vacuum battery discharged
Wi-Fi reset
• Press both buttons simultaneously for 3 seconds.
• Wi-Fi indicator (17) is flashing: Charging or process
start
• Wi-Fi indicator (17) is flashing red quickly: Error
INSTALLATION
1. Assemble the charging base, see Fig. 1.7, 1.8 and 1.9
– insert the lower part into the main section of the
charging base and secure with the locks. Then open
the upper lid and install the dust bag (if the bag is not
installed, extraction of dirt into the charging basis
cannot be activated!).
• Connect power supply cable.
Note:
• Provide a space of min. 6 cm from the wall, min. 0.5 m
on both sides of the docking station and min. 1.5 m in
front of the station.
• If the power cord is stretched vertically to the ground,
the appliance may pull it out and the docking station
may be switched off.
• In normal condition, the charging indicator light is on
when switched on, and off when charged.
2. Do not move the docking station or expose it to
direct sunlight.
Note: Direct sunlight will interfere with the docking
station signal and the appliance may not return to the
docking station properly.
3. Installing the side brush
Press the side brush to its position, see Fig. 7, until a
"click" was heard.
4. Putting the appliance into operation and charging
Press and hold the ON button for approx. 3 s. to
switch on the robot vacuum. Then place the robot
vacuum manually to the charging base thus allowing
VR3550
EN
the charging electrodes to get in contact. If the LED
indicator on the charging base goes off, the charging
process has been started.
5. Connecting a mobile app (you can skip this step)
Read the instructions for connecting Wi-Fi and connect
the mobile app.
6. Start of cleaning
After switching on the robot vacuum, briefly press the
button
on the robot vacuum or start cleaning using
the mobile app.
Note:
• The sweeping robot cannot be used to remove fluids.
• If the battery charge level is less than 15 %, the
appliance cannot operate. In this case, recharge it.
• If the battery charge level is less than 15 %, the
appliance automatically returns to the docking
station.
• Before use, remove various wires (including the
docking station power cord) from the floor to prevent
outages and damage to objects or wires when the
appliance catches these wires.
7. Installing the wiping module
a) Installing the wiping cloth: Slide the mop pad into
the mop module guide. Then put it down onto the
mop module and fasten the velcros, see Fig. 1.D and
1.E.
Note: Clean the wiping cloth after use to keep it in good
condition.
b) Remove the water tank using the unlock button and
fill it with water, see Fig. 1.B and 1.C.
c) Install the module:
Press and hold the button in the centre of the
container and slide it horizontally along the back of
the robot. The container is installed in place when
you hear a "click" sound and a voice announcement
from the appliance. After installing the container,
insert the wiping module. Once you hear a "click"
sound, the module is correctly inserted.
8. Removing the wiping module
Once the robot has completed its work, press the
latches on both pages, see Fig. 1.G, pull to the back and
clean the pad. (do not move or flip the robot during
cleaning).
Then remove the water tank and empty excessive
water.
9. Instructions for using the wiping module
• Do not use the wiping module unless supervised.
• For safety, make sure the wiping module is removed
when charging or when not in use.
• Do not attempt to wipe the carpet.
69
