Ilustrated Description - stayer BJ120 Manual De Instrucciones

Protect strawberries shocks and bumps.
The machine must be used exclusively with the cutter disk provided by the manufacturer.
If not already be in that position, set the ceiling for angles
17-0 ° (see "Adjusting the angle milling) and vertical
adjustment cap 9 to the maximum height (see "Adjustment
the top of vertical adjustment).
Place the machine with the base plate 33 facing upwards
.
Loosen and remove the screw 32 and proceed to remove
the metal cover 31.
Operate the spindle lock button 14 and hold pressed, turn
the cutter until it locks.
Loosen the lock nut wrench 24 with two pivots 23 attached,
and remove the nut. Release the lock button 14.
If found bur mounted disk 25, remove it and clean it out
through the front slot. Also remove the mounti ng flange
28 and clean.
Enter the support flange 28 in the milling spindle 29 I
ensuring it is centered above the neck 27. The support
flange must be received between both sides milled (forced
drag).
Place the cutter 25 clean disk supporting flange 28, as
stated, so that it is visible arrow direction of rotation 26
on the cutter disk. The sense of arrow must match the
direction of the arrow 13 head edge machine. The hole
Strawberry disc should be housed in the centering collar
27 of the mounting flange.
Screw the lock nut 24 on the spindle for milling 29. Tighten
the lock nut with wrench two pivots 23 while holding down
the button spindle lock 14, to retain the spindle 29.
Check if it is properly installed, without touching
Nowhere, by turning the cutter disk with hand.
Place the metal safety cover 31 so that it above the base
plate 33 and the screw fixing 32.
Tighten the screw 32.
Check if you have locked firmly plate base 33.
Inhalation of dust and shavings
Dusts from materials such as paints containing lead,
certain types of wood and some minerals and metal can
be harmful to health. Contact andinspiration of these dusts
can cause user or bystanders allergic reactions and / or
respiratory diseases.
Some powders such as oak or beech are considered as
carcinogenic, especially in combination with additives for
the treatment of wood (chromate, wood preservatives).
ENGLISH
17
materials containing asbestos must only be processed
by specialists.
- If possible use a computer for dust appropriate for the
material being worked.
- Provide good ventilation of the workplace.
- A protective mask with a filter is recommended P2 class.
Observe the relevant regulations in your country about the
working materials.
Clean the suction nozzle 21 whenever necessary and
detach the suction nozzle pulling.
Extraction with dust bag.
To make small milling work can you. use the dust bag 22.
Insert a slight twist fitting the dust bag 22 in the suction
nozzle 21.
Empty time the dust bag 22 to achieve hat the dust
extraction is optimal.
To do this, detach the dust bag 22 and drain the dust bag.

3.3 Ilustrated description

The numbering of the product features refers to the image
power tool on the graphics page.
1 One handle (isolated nip)
2 Power on / off
3 Lever tightening cap for angles
4 Scale height
5 Scale angles
6 Horizontal Center Mark
7 Anti-slip
8 rotating levers stop vertical adjustment
9 Set vertical adjustment cap
Mark width 10 Strawberry
11 Vertical Center Mark
12 Clamping lever stopper vertical adjustment
13 Arrow of direction of rotation in the housing
14 Spindle lock button
15 Auxiliary handle (insulated gripping area)
Insert plate 16
Top 17 angles
18 Rotary knob for adjusting the cutting depth
19 Lock nut setting depth
milling
20 knurled screw depth adjustment
milling
21 Suction nozzle
22 Saco dust collector
23 Wrench two pivots
24 Lock Nut
25 Strawberry disk
26 Arrow of direction of rotation of the cutter disk
27 centered neck support flange
Mounting flange 28
29 milling spindle
17