Tabla de contenido
Idiomas disponibles
Idiomas disponibles
Power tools ISL120K are designed for tightening and
loosening screws, for drilling in wood, metal, ceramic and
plastic, and impact drilling in brick, concrete and stone.
1. Contents
2.Specific safety instructions......................................13
3.Instructions for use....................................................13
3.1 Placement Tool.............................................................13
3.2 Assembly......................................................................13
3.3 Electrical connection.............................................13
3.4 Illustrated description............................................13
4.Operating instructions..............................................14
4.1 Placement and testing..........................................14
4.2 Tool change..........................................................14
5.Maintenance and service instructions.....................14
5.1 Cleaning...............................................................14
6.2 Repair service.......................................................14
5.3 Warranty...............................................................15
5.4 Disposal and recycling..........................................15
6.Regulations................................................................15
6.1 Technical Data......................................................15
6.2 EU declaration of conformity.................................15
2. Specific safety instructions
Hold power tool by insulated gripping surfaces,
Ÿ
when performing an operation where the fastener
may contact hidden wiring. Fasteners contacting a
"live" wire may make exposed metal parts of the power
tool "live" and could give the operator an electric shock.
Secure the workpiece. A workpiece clamped with
Ÿ
clamping devices or in a vice is held more secure than by
hand.
Always wait until the machine has come to a
Ÿ
complete stop before placing it down. The tool insert
can jam and lead to loss of control over the power tool.
Do not open the battery. Danger of short-circuiting.
Ÿ
Protect the battery against heat, e. g., against
continuous intense sunlight, fire, water, and
moisture. Danger of explosion.
In case of damage and improper use of the battery,
Ÿ
vapours may be emitted. Provide for fresh air and
seek medical help in case of complaints. The vapours
can irritate the respiratory system.
Use the battery only in conjunction with your
Ÿ
STAYER power tool. This measure alone protects the
battery against dangerous overload.
Use only original STAYER batteries with the voltage
Ÿ
listed on the nameplate of your power tool. When
using other batteries, e. g. imitations, reconditioned
batteries or other brands, there is danger of injury as well
as property damage through exploding batteries.
3.Instructions for use
3.1 Placement Tool
ENGLISH
13
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may
result in electric shock, fire and/or serious injury.
3.2 Assembly
page
Do not continue to press the On/Off switch after
the machine has been automatically switched off.
The battery can be damaged.
To remove the battery 5 press the unlocking buttons 9 and
pull out the battery downwards. Do not exert any force.
The battery is equipped with a temperature control which
allows charging only within a temperature range of between
0 °C and 45 °C. A long battery service life is achieved in this
manner.
Observe the notes for disposal.
3.3 Electrical connection
Battery Charging
Use only the battery chargers listed on the accessories
page. Only these battery chargers are matched to the
lithium ion battery of your power tool.
The battery is supplied partially charged. To
ensure full capacity of the battery, completely
charge the battery in the battery charger before
using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging procedure
does not damage the battery.
The lithium-ion battery is protected against deep
discharging. When the battery is empty, the machine is
switched off by means of a protective circuit: The inserted
tool no longer rotates.
Charge status indicator
The charging status indicator 10 of the magazine, is
composed of two LEDs:
Green: Displayed when the battery is charged.
Red: Displayed when the battery is charging.
Temperature Dependent Overload Protection
When using as intended for, the power tool cannot be
subject to overload. When the load is too high or the
allowable battery temperature range of 0-50 °C is
exceeded, the speed is reduced. The power tool will not run
at full speed until reaching the allowable battery
temperature.
3.4 Illustrated description
1 Screwdriver bit
2 Tool holder
3 Locking sleeve
4 Bulb
5
Battery
6
Handle
7
On/Off switch
13
Capítulos
Tabla de contenido
