Ilustrated Description; Adjustment Operations - stayer BJ120B Manual De Instrucciones

Nowhere, by turning the cutter disk with hand.
Place the metal safety cover 31 so that it above the base
plate 33 and the screw fixing 32.
Tighten the screw 32.
Check if you have locked firmly plate base 33.
Inhalation of dust and shavings
Dusts from materials such as paints containing lead,
certain types of wood and some minerals and metal can
be harmful to health. Contact andinspiration of these dusts
can cause user or bystanders allergic reactions and / or
respiratory diseases.
Some powders such as oak or beech are considered as
carcinogenic, especially in combination with additives for
the treatment of wood (chromate, wood preservatives).
materials containing asbestos must only be processed
by specialists.
- If possible use a computer for dust appropriate for the
material being worked.
- Provide good ventilation of the workplace.
- A protective mask with a filter is recommended P2 class.
Observe the relevant regulations in your country about the
working materials.
Clean the suction nozzle 21 whenever necessary and
detach the suction nozzle pulling.
Extraction with dust bag.
To make small milling work can you. use the dust bag 22.
Insert a slight twist fitting the dust bag 22 in the suction
nozzle 21.
Empty time the dust bag 22 to achieve hat the dust
extraction is optimal.
To do this, detach the dust bag 22 and drain the dust bag.

Ilustrated description

The numbering of the product features refers to the image
power tool on the graphics page.
1 One handle (isolated nip)
2 Power on / off
3 Lever tightening cap for angles
4 Scale height
5 Scale angles
6 Horizontal Center Mark
7 Anti-slip
8 rotating levers stop vertical adjustment
9 Set vertical adjustment cap
Mark width 10 Strawberry
11 Vertical Center Mark
12 Clamping lever stopper vertical adjustment
13 Arrow of direction of rotation in the housing
14 Spindle lock button
15 Auxiliary handle (insulated gripping area)
Insert plate 16
Top 17 angles
18 Rotary knob for adjusting the cutting depth
19 Lock nut setting depth
milling
20 knurled screw depth adjustment
milling
21 Suction nozzle
22 Saco dust collector
ENGLISH
19
23 Wrench two pivots
24 Lock Nut
25 Strawberry disk
26 Arrow of direction of rotation of the cutter disk
27 centered neck support flange
Mounting flange 28
29 milling spindle
30 Arrow of direction of rotation of the spindle for milling
Top 31 metal
32 Screw for fixing the metal plate
33 Motherboard
The accessories illustrated or described are not within the
material attached as standard. The full range of
accessories can be found in our program accessories.
3. Operating instructions

Adjustment Operations

Adjusting the cutting depth
The knob 18 can set the depth of fresado.El knob can be
locked in three positions different height for different sizes
of biscuit.
Interrelationship between locking heights, cookies, and
milling depths:
Height
locking
0
10
20
S
D
By employing disc cutters sharp it may be necessary
readjust the cutting depth. For this, loosen the lock nut 19.
Turning to the effect clockwise the knurled screw 20 can
be reduced milling depth, and vice versa. Take a milling
Test for controlling the cutting depth adjusted. Once com-
pleted the adjustment, tighten the locking nut 19.
Adapting the top of vertical adjustment
The top vertical adjustment 9 allows you to set the dis-
tance between the upper face of the piece and the slot
milling.
To mount the top of vertical adjustment 9 seat it against
stop for angles 17 and round it with the dial 8 against stop
guide for angles.
Note: Do not exert any force to During installation!
When mounted in the correct position, the stop 9
slides smoothly.
Set the dial 8 according to the desired distance scale hei-
ght 4. Close then the levers 12 tightening.
To position the slot in the middle is necessary to adjust
vertical to the top half of the setting part thickness.
To remove the top of vertical adjustment loosen the lever 9
12 and actuate clamping levers 8 for rotating remove the
stop up the top for 17 angles.
Adjusting the angle milling
The stop 17 allows to make angles with ease milled in
mitered seams. To reset the stop angles loosen the levers
17 Tightening 3. Tilt the top angles until the desired angle
19
Milling depth
biscuit
in mm
Nº0 8
Nº10 10
Nº20 12.3
Simplex 13
Duplex 14.7