Idiomas disponibles
Idiomas disponibles
en
ENGLISH
Additional Warnings:
WARNING
drilling, and other construction activities
contains chemicals known to cause cancer,
birth defects or other reproductive harm. Some
examples of these chemicals are:
• Lead from lead-based paints,
• Crystalline silica from bricks and cement and
other masonry products, and
• Arsenic and chromium from chemicallytreated
lumber.
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well
ventilated area, and work with approved safety
equipment, such as those dust masks that are
specially designed to filter out microscopic
particles.
3.5
Safety instructions for battery packs:
Protect battery packs from water and
moisture!
Do not expose battery packs to naked flame!
Do not use faulty or deformed battery packs!
Do not open battery packs!
Do not touch or short-circuit battery packs!
Slightly acidic, flammable fluid may leak from
defective Li-ion battery packs!
If battery fluid leaks out and comes into
contact with your skin, rinse immediately
with plenty of water. If battery fluid leaks out
and comes into contact with your eyes, wash them
with clean water and seek medical attention
immediately.
Transport of li-ion battery packs:
The shipping of li-ion battery pack is subject to laws
related to the carriage of hazardous goods (UN
3480 and UN 3481). Inform yourself of the currently
valid specifications when shipping li-ion battery
packs. If necessary, consult your freight forwarder.
Certified packaging is available from Metabo.
Only send the battery pack if the housing is intact
and no fluid is leaking. Remove the battery pack
from the machine for sending. Prevent the contacts
from short-circuiting (e.g. by protecting them with
adhesive tape).
SYMBOLS ON THE TOOL:
V...............volts
.......... direct current
rpm ......... revolutions per minute
.../min ..... revolutions per minute
n ............. rated speed
4. Overview
See page 2.
1 Button for adjusting the hand guard
8
California Prop 65 08_2018
Some dust created by power
sanding, sawing, grinding,
2 Hand protection
3 Extension arm
4 Additional handle / Additional handle with vibration
damping *
5 Sliding on/off switch
6 Electronic signal indicator
7 Battery pack release button
8 Capacity indicator button
9 Capacity and signal indicator
10 Battery pack *
11 Dust filter *
12 Adjusting nut
13 Accessory *
14 Support flange
15 Spindle
16 Allen key
17 2-hole spanner
* depending on equipment/not in scope of delivery
5. Initial Operation
5.1
Attaching the additional handle
Always work with the additional handle
attached (4)! Attach the additional handle on
the left or right of the machine and secure.
5.2
Attaching the hand guard
Always work with the hand guard (2) attached.
Inserting:
- Press and hold the button (1).
- Slide the hand guard (2) into the slot from the
bottom to the top as shown (see illustration,
page 2). First slide the glider with the widest
diameter approx. 5 mm into the external slot. Then
slide the glider with the smallest diameter into the
inner slot.
Note: Do not try to slide both gliders into both slots
at the same time, as this will not work. Start with
the external glider, and the inner glider will follow
automatically.
Turning:
- Press the button (1) and turn the hand guard until
the closed section is facing the operator.
- Make sure that the guard is securely positioned:
The button (1) must engage and you should not be
able to turn the safety guard.
5.3
Dust filter
See illustration A on page 2.
Always fit the dust filter if the surroundings are
heavily polluted (11).
The machine heats up faster when the dust
filter is fitted (11). It is protected by the
electronics system from overheating (see
chapter9.).
To fit:
See fig. A, page 2. Attach the dust filter (11) as
shown.
To remove:
