Idiomas disponibles
Idiomas disponibles
TRANSLATION OF
THE ORIGINAL INSTRUCTIONS
IMPACT DRILL
58G712
CAUTION: BEFORE USING THE POWER TOOL READ THIS MANUAL
CAREFULLY AND KEEP IT FOR FUTURE REFERENCE.
DETAILED SAFETY REGULATIONS
Wear ear protectors when impact drilling. Exposure to noise
a)
can cause hearing loss.
Use auxiliary handle(s), if supplied with the tool. Loos of
b)
control can cause personal injury.
Hold power tool by insulated gripping surfaces, when
c)
performing an operation where the cutting accessory may
contact hidden wiring or its own cord. Cutting accessory
contacting a "live" wire may make exposed metal parts of the
power tool "live" and could give the operator an electric shock.
Avoid touching rotating parts. Touching of rotating power
d)
tool parts, equipment in particular, may cause body injury.
Wait until power tools comes to a complete stop before
e)
putting it away. Working tool may jam and cause loss of
control over the power tool.
In case of working tool jam immediately switch off the
f)
power tool, also be prepared for high reaction torque.
Fix processed material to stable surface and secure with
g)
clamps or vice to eliminate shifting. This kind of workpiece
fixation is safer than holding the workpiece in hand.
Description of improper use: Do not throw the power tool, do
h)
not overload, do not immerse in water or other fluids, do not
use for mixing adhesive or cement mortars, do not hang, carry,
pull or unplug the power tool by pulling the cord.
CAUTION! This device is designed to operate indoors. The design
is assumed to be safe, protection measures and additional safety
systems are used, nevertheless there is always a small risk of
injuries at work.
CONSTRUCTION AND USE
Impact drills are hand operated power tools with insulation class II.
Tools are driven by single-phase commutator motors with rotational
speed reduced with gear transmission. This type of power tools is
widely used for making holes in wood, wood-like materials, metals,
ceramics and plastics (rotation only), and concrete, bricks and
alike (with impact). Range of use covers repair and building works,
woodworking and any work from the scope of individual, amateur
activities (tinkering).
Use the power tool according to the manufacturer's instructions
only.
DESCRIPTION OF DRAWING PAGES
Below enumeration refers to the device elements depicted on the
drawing pages of this manual.
Drill chuck
1.
Operation mode switch
2.
Switch lock button
3.
Direction selector switch
4.
Speed control wheel
5.
Switch
6.
Additional handle
7.
Depth gauge rod
8.
Gear switch
9.
* Slight differences may appear between the product and drawing.
MEANING OF SYMBOLS
CAUTION
WARNING
ASSEMBLY/SETTINGS
INFORMATION
EQUIPMENT AND ACCESSORIES
Key - handwheel
1.
Additional handle
2.
Depth gauge rod
3.
PREPARATION FOR OPERATION
INSTALLATION OF ADDITIONAL HANDLE
Due to personal safety issues it is recommended to always use
the additional handle (7). Possibility to rotate the additional
handle before it is clamped on the drill body allows choosing
the position most comfortable for specific working conditions.
Disconnect the power tool from power supply.
• Loosen the wheel lock that locks collar of the locking handle (7) by
turning it counter-clockwise.
• Slide the handle collar over cylindrical part of the drill body.
• Turn for the most comfortable position.
• Turn the wheel lock clockwise tightly to clamp the handle.
DEPTH GAUGE INSTALLATION
Depth gauge (8) serves to limit the depth of drill penetration of
material.
• Loosen the wheel lock, which blocks collar of the additional
handle (7).
• Slide depth gauge rod (8) into the hole in the additional handle
collar.
• Set desired drill depth.
• Fix by tightening the wheel lock.
INSTALLATION OF WORKING TOOLS
Disconnect the power tool from power supply.
• Insert key into one of the holes on the side wall of the drill chuck
(1).
• Open jaws to desired dimension.
• Insert cylindrical drill shank into the chuck, push it to the limit.
• Tighten jaws on drill shank with the key (insert it into three holes
on the chuck side wall).
Remember to always remove the key from the chuck after you
finish drill installation or removal.
When a new drill is installed, observe against excessive drill wobble
after start-up. This may indicate improper fixing in the chuck or
deviated drill. If you observe wobbling, check fixing of the drill and
its technical condition. Check drill chuck on a regular basis, before
each use of the drill.
OPERATION / SETTINGS
SWITCHING ON / SWITCHING OFF
The mains voltage must match the voltage on the rating plate of
the drill.
Switching on – press the switch button (6) and hold in this position.
Switching off – release pressure on the switch (6).
Locking the switch (continuous operation)
10
- 1 pce
- 1 pce
- 1 pce
