Idiomas disponibles
Idiomas disponibles
PR GRAMMI G
PR GRAMMI G M
he digitiser can only be programmed via the
programming terminal Ref.1038/55.
The programming terminal can be connected in
either of the following ways:
ocally, to the programming connector ( ) on the
bac of the digitiser to be programmed.
To another calling module, concierge switchboard
or digitiser in the system.
To any passi e wiring junction box (Ref. 1038/90)
connected to the system.
PARAM
R
The
following
parameters
will
need
programmed:
P
A
I G
A I
This step is used to select the operati e method.
The digitiser can be con gured either as a main or
a secondary de ice.
hen con gured as a main de ice, the digitiser
sends calls to apartment phones in the range from
0 to
.
hen the digitiser is con gured as
a secondary de ice, it sends calls to apartment
phones in its riser.
A
I G
A I
M
R
Each calling station, main and secondary, is
identi ed by a number. The possible numbers which
can be assigned to a calling station depend on the
calling station type. A number from 1 to
assigned if the digitiser is a main de ice. A number
from 1 to
can be assigned if the digitiser is a
secondary de ice. In the latter case, the number
identi es the riser that the digitiser belongs to.
IM
The busy time is the minimum duration of a oice
communication from when the call is made. This
alue can be set in the same way on all the calling
de ices and can be 10, 0, 30, 0s.
16
RI A
MA AG M
Two door opener strategies can be implemented:
free or pri ate. The performance depends of the
station type:
Main: free door opener: the digitiser will open
the door following the re uest from any decoder
pri ate door opener: the digitiser will open the
door following a re uest from the door phone with
which the con ersation was established.
econdary: free door opener: the digitiser will
open the door following the re uest from any
decoder in its riser pri ate door opener: the
digitiser will open the door following a re uest
from the door phone with which the con ersation
was established.
This setup will not ha e effect on door opener
re uests from the concierge switchboard since, in
this case, the digitiser will open the door regardless
of the strategy.
to
be
R
P
I G IM
The door opening time is the time for which the
electrical loc relay is energised. This time can be
0-30s. 0 means that the relay is energised with a
single pulse.
A
IM
The tone duration on a door phone (or concierge
switchboard when it is called from a main digitiser)
depends on the calling digitiser setup. This alue
can be included between 1 and
M
R
I
I
There can be one or two independent
can be
lines physically in the section between main and
secondary de ices. If there is only one line, this
channel must be engaged by the digitiser.
ZZ R
M
The
olume of the digitiser buzzer can be
programmed on three le els: low, medium, high.
A
PR GRAMMI G
A user code included in the range from 0 to
regardless of the digitiser type and code can be
associated to each of the 10 connectable buttons.
efa lt settings
The default settings of the de ice are:
DIGITISER T
A
ING STATI N
S TIME
E E TRI A
MANAGEMENT
D
R
ENING TIME
A
T NE TIME
N M ER
ZZER
DIGITISER ID
A
TT NS
PR GRAMMI G IA
The system must be on for programming ia the
terminal.
he terminal m st r n irm are version .0 or later.
old the " N" button pressed for longer than
three seconds to switch the terminal on.
lug the programming wire in the speci c soc et
seconds.
( ) or, alternati ely, in another calling module,
concierge switchboard or passi e wiring junction
box. The terminal will be automatically connected
to the data line and the following will appear on
the display for three seconds:
oice
Then the following will appear:
Search by:
Select the Serial number option. The following
will appear:
DS1038-013
DS1038-013
E
MAI
DE
Enter the digitiser serial number (S/N on the label
- 10) and press " ". The following will appear:
0 seconds
PRI A
0 seconds
3 seconds
At this point, the terminal is logically connected
to the digitiser (DIG) with the selected serial
I E INES 1
number ("xyzxyz"). The following will appear on
the module display to indicate that the module is
ME
M
I M
in "Maintenance" status.
IA ...........
rrrr
reserved code
At the point, program the digitiser con guration
RMI A 1038/55
parameters, on six pages:
( age 1: De ice found (DIG) and serial number, neither
can be edited Installation location description)
( age : Type, ode, usy time, oc management)
rogramming
( age 3: all time, no. of lines, uzzer olume)
Serial number
Type
Ac uisition
to scroll, the " " ey to con rm and to program all
the parameters.
Serial number:
000000
DIG
SN:u wxyz
------------------------------
ia................................
: in "Maintenance" status, the digitiser can
manage the electrical loc when door opener
code is entered, the hall button is pressed or
the postal ey contact is inserted.
DIG
SN:u wxyz
------------------------------
ia................................
Type:
od:001
------------------------------
usy:10 s
pener:S-00 s
all:03 s
ines: 1
uzzer:
se the alphanumeric eys, the " " and " " eys
ress "Esc" to go to the following page:
1
