Idiomas disponibles
Idiomas disponibles
Charging time for
5.0 Ah
battery capacity,
6.0 Ah
approx. (At 20°C)
1.5 Ah
(× 2 unit)
Charging time for
multi volt battery
2.5 Ah
capacity, approx.
(× 2 unit)
(At 20°C)
4.0 Ah
(× 2 unit)
Number of battery cells
Charging voltage for USB
Charging current for USB
Weight
NOTE
○ The recharging time may vary according to the ambient
temperature and power source voltage.
○ If charging takes a long time
–
Charging will take longer at extremely low ambient
temperatures. Charge the battery in a warm location
(such as indoors).
–
Do not block the air vent. Otherwise the interior will
overheat, reducing the charger's performance.
–
If the cooling fan is not operating, contact a HiKOKI
Authorized Service Center for repairs.
4. Disconnect the charger's power cord from the
receptacle.
5. Hold the charger firmly and pull out the battery.
NOTE
Be sure to pull out the battery from the charger after
use, and then keep it.
Regarding electric discharge in case of new
batteries, etc.
As the internal chemical substance of new batteries and
batteries that have not been used for an extended period is
not activated, the electric discharge might be low when
using them the first and second time. This is a temporary
phenomenon, and normal time required for recharging will
be restored by recharging the batteries 2–3 times.
How to make the batteries perform longer.
(1) Recharge the batteries before they become completely
exhausted. When you feel that the power of the tool
becomes weaker, stop using the tool and recharge its
battery. If you continue to use the tool and exhaust the
electric current, the battery may be damaged and its life
will become shorter.
(2) Avoid recharging at high temperatures. A rechargeable
battery will be hot immediately after use. If such a
battery is recharged immediately after use, its internal
chemical substance will deteriorate, and the battery life
will be shortened. Leave the battery and recharge it
after it has cooled for a while.
MOUNTING AND OPERATION
Action
Inclined cutting using the guide
(+45° direction)
32 min
Charging
38 min
Fine tuning of parallelism of base
20 min
sides and saw blade
Fine tuning of inclination angle
32 min
(When 90°)
Fine tuning of inclination angle
52 min
(When 45°)*
Fine tuning of guide piece position
4–10
Adjusting the cutting depth
5 V
Cutting line
2 A
Switch operation
0.6 kg
About the mode select function*
Using the LED light
Attaching the guide
How to use the dust collection nozzle
Sawing with a guide rail
(sold separately)*
How to use the guide rail
(sold separately)*
Removing and inserting the battery
Cutting at right angles
Inclined cutting (+45° direction)
Dismounting the saw blade
Mounting the saw blade
Remaining battery indicator
Charging a USB device from a
electrical outlet
Charging a USB device and battery
from a electrical outlet
How to recharge USB device
When charging of USB device is
completed
Selecting accessories
*1 Tighten the angle adjustment screw that is at the rear
until it makes contact, and then turn it one full rotation
back in the opposite direction. (Fig. 13-a, Fig. 13-b)
*2 About the mode select function
Each time the mode selector switch is pushed, the
operation mode changes.
When Silent mode is selected, the Silent mode indicator
lamp lights up.
Silent mode reduces maximum motor RPM enabling
efficient work with less noise.
Figure
Page
Mode
Power
9
3
Silent
17
Action
1
2
3
4
No-load speed
4500 min-
2500 min-
English
Figure
Page
10
3
11
3
12
4
13
4
14
4
15
5
16
5
17
5
18
5
19
5
20
5
21
6
22
6
23
6
24
6
25
7
26
7
27
8
28
8
29
9
30-a
9
30-b
9
31
9
32
9
―
269
1
1
