Maintenance / Disposing; Technical Data; Special Accessories - Martin Yale Intimus 315SC2 Instrucciones De Uso

Translation of the Original Operation Manual
GB
Übersetzung der Originalbetriebsanleitung
MATERIAL JAM IN THE MACHINE:
(Auto reverse function)
If a jam is caused by too much material being fed in
the following happens:
- The cutters jam, then run in reverse for a short
time (material is released) and stop. The motor
switches off. The control display
on.
Proceed as follows:
Paper jam in paper feed slot (12)
- Remove the paper that has been fed back.
- The cutters now run forwards automatically and
shred the remaining paper in the cutters. During
the forward run the forward button (3) LED
display comes on. The control display
goes out.
- Continue shredding with less paper.
Material jam in CD/DVD feed slot (13)
- Remove the returned material.
Remove the material
because there is the risk of being
injured by the sharp cut surfaces.
- The remaining material to be cut is now
automatically fed to the cutters again and
shredded. During the forward run the forward
button (3) LED display comes on. The control
display (6) goes out.
- If the material to be cut has gone through continue
shredding with the right amount of material.
- If necessary, switch the cutters manually
alternately from forward to reverse until the
material has gone through completely and been
shredded.
CLEANING THE PHOTOCELLS (Fig. 5):
If paper particles should come to rest in the inlet
guide (for example after a paper jam) it is possible
that the machine will not turn off, due to the broken
light barrier.
fi g. 5
Model Cutting width
paper / CD,DVD
intimus 315/319SC2 5.8 mm / 8 mm
intimus 315/319SC2 3.8 mm / 8 mm
intimus 315/319CC3 3.8x36 mm/ 8 mm
intimus 315/319CC4 1.9x15 mm / 8 mm
Model
intimus 315/319SC2 220-230V/50Hz, 7.8 amps
intimus 315/319SC2 220-230V/50Hz, 7.8 amps
intimus 315/319CC3 220-230V/50Hz, 7.8 amps
intimus 315/319CC4 220-230V/50Hz, 7.8 amps
MALFUNCTIONS
SIMULTANEOUS MATERIAL FEED:
Should material be fed into the two feed slots at the
same time the following happens:
- The cutters jam, then run in reverse for a short
time (material is released) and stop. The motor
switches off. The control display
(6) comes on.
- Take the material out of one of the slots.
- Press the forward button (3) briefl y. The material
in the other slot is fed to the cutters and shredded.
The control display
LIGHT BARRIER OCCUPIED
WHEN THE WASTE BIN MOVES OUT:
(6)
If there is still material in one of the two feed
slots when the waste bin is moved out, the motor
switches off and the cutters stop. The control
display (6) comes on.
Push the waste bin in again and acknowledge
carefully
the status by briefl y pressing the forward button
(3). The existing material is fed to the cutters and
shredded.
LIGHT BARRIER COVERED
WHEN MACHINE TURNED ON:
Should there still be material in one of the two feed
slots when the machine is switched on the control
display (6) comes on.
Remove the material and acknowledge the status
by pressing the forward button (3) briefl y.

MAINTENANCE / DISPOSING

To remove these paper strips and also to clean the
photocell, pass another sheet of paper through the
feed slot, or switch the machine to reverse and wipe
both "eyes" of the photocell with a brush.
CUTTER MAINTENANCE (CROSS CUT):
Cross cut cutters must be oiled after a
specifi c operating time. If the control display
(7) comes on proceed as follows:
Pour a little oil onto a sheet of paper and then feed this
through the paper feed slot (12) onto the cutters. The
paper is drawn in and in this way the oil is distributed
to the cutters.
Note: This procedure is acknowledged as follows
to turn off the display after the cutters have been
oiled:
- Press the reverse button
down until the control display

TECHNICAL DATA

Cutting capacity Working width
paper / CD,DVD
35-38 sheets* / 1 piece 310 mm
31-33 sheets* / 1 piece 310 mm
23-25 sheets* / 1 piece 310 mm
15-17 sheets* / 1 piece 310 mm
Power supply data
supply voltage / frequency / current consumption
115-125V/60Hz, 14.9 amps
115-125V/60Hz, 14.9 amps
115-125V/60Hz, 14.9 amps
115-125V/60Hz, 14.9 amps
MOTOR PROTECTION:
Should the motor be overloaded it switches off. The
control display
The machine can be started again after a cooling
down period of about 25 – 40 minutes (depending
(6) comes on the model and the room temperature).
ELECTRICAL FAULT:
If the control display
the function button (2) LED display
(6) goes out.
control display (8)
fault. The machine cannot be started.
In this case please contact your dealer.
FAULT CHECK LIST:
Should the machine not work, check the following
points:
- is the plug connected to the power supply?
- is the waste bin pushed in?
- is the waste bin (14) full?
- Is there a material jam in the machine?
- Is the motor overloaded?
If none of these test points apply, please
contact your dealer.
The cutters now start a cleaning cycle automatically
(forward and reverse run) and then switch off. The
machine is ready for use again. Should you need to re-
order the special oil see "SPECIAL ACCESSORIES".
AUTOMATIC ENERGY SAVING:
If the machine is not used for a while it automatically
switches off after about 5 minutes. The function button
(2) LED display
function button briefl y to turn it on again.
DISPOSING OF THE MACHINE:
(4) and keep it held
(7) goes out.
Power Noise level Intermittent operation
1.8 kW app. 57 dB(A)
1.8 kW app. 57 dB(A)
1.8 kW app. 57 dB(A)
1.8 kW app. 57 dB(A)
Description
100V/50/60Hz, 18.0 amps
Lubricant, 110 ml bottle
100V/50/60Hz, 18.0 amps
Note: For orders of special accessories and spare
100V/50/60Hz, 18.0 amps
parts, please contact your dealer.
100V/50/60Hz, 18.0 amps
7
(9) comes on.
(9) fl ashes together with
fl ashes there is an electrical
Follow the instructions under "EMPTYING THE
WASTE BIN".
Follow the instructions in "MATERIAL JAM IN
THE MACHINE".
See "MOTOR PROTECTION".
for "Ready" goes out. Press the
Dispose of the machine in an environmentally
friendly fashion at the end of its useful service
life. Do not dispose of any of the parts
included in the machine or its packaging with
household waste.
Dimensions
ON / OFF W x D x H
45 / 60 min 790 x 926 x 1297 mm
45 / 60 min 790 x 926 x 1297 mm
45 / 60 min 790 x 926 x 1297 mm
45 / 60 min 790 x 926 x 1297 mm
* based on A4-paper 70g/m² at 230V/50Hz – 10%

SPECIAL ACCESSORIES

or only the
Weight
81/98 kg
81/98 kg
82/99 kg
82/99 kg
Order-No.
88035