Maintenance / Disposing; Technical Data - Martin Yale intimus 3000S Instrucciones De Uso

GB
Translation of the Original Operation Manual
Übersetzung der Originalbetriebsanleitung
OPERATION
EMPTYING THE RECEPTACLE (Fig. 3):
Proceed as follows:
- Remove the receptacle from in front of the ma-
chine and empty its contents. Pilot lamp lights
up (7) (fig. 1).
- Replace the empty receptacle under the machine
and push all the way to the back.
Note: The machine will only run when the recepta-
cle is pushed completely under the machine.
4 mm
11
fig. 3
MATERIAL JAM IN MACHINE:
(Auto-reverse-function)
If too much material is fed in, causing a jam, the
machine will respond as follows:
- Cutting mechanism halts, then runs one step in
reverse (material will be released) and stops.
- The motor shuts down automatically.
- The pilot lamp (5) (fig. 1) lights up.
Proceed as follows:
Paper jam in the paper feed slot (9)
- Tear off the returned paper just above the feed
slot.
- Briefly move the rocker switch (1) (fig. 1) to the
" " position.
- The pilot lamp (5) (fig. 1) goes out.
- The cutting system then runs forward and shreds
the paper remaining in the cutter.
- Continue shredding, feeding smaller quantities
of paper.
Material jam in the CD/DVD feed slot (10)
- Remove the returned material.
Take care when removing material as
sharp edges may cause injury!
- Briefly move the rocker switch (1) (fig. 1) to the
" " position.
- The pilot lamp (5) (fig. 1) goes out.
- The remaining material to be shredded is then
fed to the cutting system again.
- Once the remaining material has been shred-
ded, continue shredding, feeding the correct
quantities.
Description
Plastic bag, 300 x 300 x 700 x 0,018 mm
Lubricant, 110 ml bottle
Note: For orders of special accessories and spare parts, please contact your dealer.
CLEANING THE PHOTOCELLS (fig. 4):
If paper particles should come to rest in the inlet
guide (for example after a paper jam) it is pos-
sible that the machine will not turn off, due to the
broken light barrier.
To remove these paper strips and also to clean
the photocell, pass another sheet of paper through
the feed slot, or switch the machine to reverse and
wipe both „eyes" of the photocell with a brush.
3,8x48
mm
MALFUNCTIONS
- If necessary, move the cutting system manually
to and fro between forward and reverse running
until all the material has been fed through and
shredded.
MOTOR PROTECTION:
The motor shuts down automatically, should it
become overloaded. The pilot lamp (6) (fig. 1)
lights up. Turn the machine off with the pushbutton
switch (1) (fig. 1).
Allow the motor to cool down for 50 to 55 minutes
(depending upon room temperature) and then
continue shredding.
CHECKLIST IN CASE OF MALFUNCTIONS:
If the device does not function, check the follo-
wing:
- Is the plug connected to the mains?
- Is the pushbutton switch (1) on?
- is the receptacle placed properly under the
machine?
- is the receptacle full?
The receptacle has to be emptied.
- is there a material jam in the machine?
Follow the instructions under "MATERIAL
JAM"
- has the motor been overloaded?
Wait until the motor has cooled, and then re-
start.
If none of the above applies, please contact
your dealer.
ACCESSORIES

MAINTENANCE / DISPOSING

3
fig. 4
Wait each time until the motor stops
before switching direction!
Order-No.
5
MAINTANENCE OF THE
CUTTING MECHANISM (3,8x48 mm):
Cross-cut cutting mechanism should be
oiled regular after a certain operating time
to maintain the cutting performance.
This can be easily accomplished if you
pour special shredder oil (Order-No. see
ACCESSORIES) as shown on a sheet of
paper and feed it through the inlet guide
to the cutting mechanism (fig. 5).
TIP FOR ENERGY SAVING:
Please make sure that the shredder is switched off
over night (pushbutton switch (1) (fig. 1).
DISPOSING OF THE MACHINE:
Dispose of
environmentally sound fashion at the
end of its useful service life. Do not
dispose of any of the parts included
in the machine or its packaging with
household trash.

TECHNICAL DATA

Cutting width:
3000S:
3000C:
Cutting capacity paper:
3000S:
3000C:
Cutting capacity
Credit cards/CD's/DVD's:
Supply voltage:
Pre-fusing:
Noise level:
Power:
Intermittent operation:
Dimensions:
Width:
Depth:
99925
Height:
88035
Weight:
the machine in an
fig. 5
4 mm
3.8x48 mm
20-22 sheets (70g/m )
2
13-16 sheets (70g/m )
2
feed one at a time
230V/50Hz
240V/50Hz
120V/60Hz
10 amps (slow-blow)
approx. 62 dB(A)
0.37 kW
5 min ON
55 min OFF
420 mm
340 mm
660 mm
ca. 15kg