ENGLISH
Note: If you want to carry out a more thorough cleaning cycle of the inside parts of the device,
use a 1:4 solution of vinegar and water, or use descaling product. Repeat this process just with
water to remove any rests.
3. OPERATION
-
Fill the water tank without exceeding the MAX mark. Use mineral water for better
maintenance of the device.
-
Connect the coffee machine to a power supply and make sure the steam knob is in the off
position. Turn on the coffee machine.
Espresso
-
While the machine preheats, place the desired coffee filter in the portafilter and fill it with
coffee powder. Use the measuring spoon/coffee tamper to pour and press coffee down. 1
tablespoon is equal to 1 coffee dose. Clean the excess coffee from the filter's edge. Fig. 3.
-
Insert the portafilter in the device and lock it tightly. Fig. 4.
-
Once the 1 coffee and 2 coffees light indicators switch from blinking to steady, press the
desired coffee button for the machine to brew 1 or 2 coffees.
Note: Make sure you have previously placed an appropriate cup or cups under the coffee spout.
Capsules
-
Remove the cap located at the bottom of the filter by turning it anticlockwise.
-
Insert the pod. The smooth side of the pod should touch the cap when replacing it. Fig. 5.
-
Place the cap and secure it by turning it clockwise.
-
Place the filter inside the filter holder and insert the brewer arm into the device.
-
Press the 1 coffee button to prepare one coffee or the 2 coffee button to prepare two
coffees or a double coffee.
Note: Allow the device to cool and remove the capsule carefully to avoid burns.
Milk froth
-
With the machine switched on and preheated, press the steam button. The steam indicator
light will flash and then remain steady when the preheating process is complete.
-
Pour milk into the container where you want to froth milk. Fill up 1/3 of the container.
-
Recommendation: It is recommended to use cold whole milk for optimal results.
-
Place an empty glass under the frother, turn the steam selector to the steam/water
position, and let the tube emit steam before frothing the milk. Once steam is emitted,
deactivate the steam function by returning the steam selector to the off position, insert
40
CAFELIZZIA 790 STEEL DUO
the 1-cm steam tube into the milk, and turn the steam selector slowly counterclockwise
until steam is produced.
Fig. 6.
1. Off
2. Steam/water
Note: The steam tube might emit some water droplets before producing steam.
When milk temperature starts to rise (to up to 75 ºC) and milk froth volume starts increasing,
turn the steam knob clockwise to the 0 position and press the steam button to stop the steam
function.
Warning: clean the steam outlet with a wet sponge immediately after use. Then, remove the
steam tube and clean the duct interior part. Moreover, it is advisable to emit steam into an
empty glass to get rid of any traces of milk left.
Hot water
-
With the coffee machine switched on and preheated, turn the steam selector to the steam/
water position. The steam tube will start dispensing hot water.
-
Turn the steam tube back to the 0 position to deactivate this function.
Memory function
-
Once the coffee machine has preheated and 1 espresso and 2 espresso light indicators
remain steady, hold down the 1 espresso button. The machine will start brewing coffee.
-
When you have obtained the desired amount of coffee, stop pressing the espresso button.
The machine will emit a sound, indicating it has saved the quantity.
-
The coffee machine brews coffee 60 seconds approx. by default, which is the maximum
time coffee can be brewed and saved.
Note: If the button is hold pressed too little time, the setting will not be saved.
If you wish to change the default amount for 2 coffees, perform the above steps using the 2
coffees button.
Factory settings
If you want to restore factory settings, hold pressed the 1 coffee button and the steam button
for 3 seconds. The device will beep once indicating factory settings have been successfully
restored.
ENGLISH
41
CAFELIZZIA 790 STEEL DUO