Tabla de contenido
Idiomas disponibles
Idiomas disponibles
To cancel the lock down, press the
In order to deacti vate the control unit without the remote control, turn on the
igniti on and press the MASTER BUTTON. If the presence functi on is acti vated, the
locks menti oned in secti ons 6.1 (Anti -theft through the DOOR) and 6.2 (Anti -theft
functi on in the IGNITION) will not be functi oning.
LOCK TEST BY PRESENCE
7
Turn the igniti on on (or the car is on) hold down the
1P control unti l the led goes out and blinks twice, wait for the lock ti me.
VALET PARKING FUNCTION
8
If you need to leave your vehicle at the mechanic, carwash, a place with valet service
or other such places, you can acti vate the valet functi on without showing them where
the MASTER BUTTON is or giving them the presence control.
Press the MASTER BUTTON 3 ti mes, it will emit 2 beeps, the locks menti oned in items
6.1, 6.2 and 6.3 are temporarily disabled. Each ti me the igniti on is turned on or off ,
it will emit 2 beeps to warn the user that the vehicle is unprotected. To acti vate the
anti -theft functi ons again press the MASTER BUTTON once. When using the presence
functi on you need to press
on the CX-1P presence control near the car.
Press
3 quick taps on the
Disables the locks menti oned in
MASTER BUTTON
secti ons 6.1, 6.2 and 6.3
1 quick tap on the
Enables the locks menti oned in
MASTER BUTTON
secti ons 6.1, 6.2 and 6.3 (If enabled)
ENABLE OR DISABLE ALARM
9
The control panel can be switched on and off by programming (see table secti on 18,
functi on 9).
MASTER BUTTON
10
This MASTER BUTTON needs to be installed in a concealed but easily accessible place.
From this bu� on you can confi gure alarm functi ons (see secti on 18).
DISABLE ALARM WITHOUT CONTROL
11
If you lose your remote control, you can deacti vate the control panel by turning the
igniti on on and touching the MASTER BUTTON.
PROGRESSIVE LOCK CYCLE
12
LOCK FOR
UNLOCK
2 SECS.
FOR 10 SECS.
COMPLETELY
UNLOCK
LOCKED
FOR 2 SECS.
18
on the presence control.
bu� on and press
on the CX-
Functi on
Alarm Response
Siren emits 2
beeps
No beeps
LOCK FOR
UNLOCK
2 SECS.
FOR 5 SECS.
LOCK FOR
2 SECS.
AUTOMATIC ALARM ACTIVATION
13
If the alarm is enabled and disabled and nothing happens aft er it is disabled, the alarm
will be acti vated again. If there is any change in the igniti on, doors or hood during this
ti me, the alarm will not be acti vated. This functi on can be programmed (see secti on 18).
SOUND CONTROL
14
This output allows you to acti vate and deacti vate the radio/sound/video of the vehicle
using the alarm. The sound control output is ON, in the following situati ons:
• When energizing the alarm / When the igniti on is on with the alarm off / When
opening the door with alarm off and igniti on off / Disabling the alarm aft er a violati on
/ When unlocking using the presence control.
The sound control output is turned OFF in the following situati ons:
• When acti vati ng the alarm / When the lockdown warning begins/ When signaling
that you are in valet mode. NOTE: If the sound equipment requires a control current
greater than 150 mA, use an external relay.
15
ULTRASOUND ADJUSTMENT
The ultrasound has 4 levels of sensiti vity:
Warning
1 Beep
2 Beeps
3 Beeps
4 Beeps
NOTE: When the alarm is off and the vehicle has a door open, you will noti ce a visible light as the
ultrasonic sensor detects movement. This facilitates adjusti ng the sensor for each vehicle.
BACKUP BATTERY
16
The alarm has an auxiliary power circuit that takes over if the vehicle's ba� ery is
disconnected. The auxiliary power supply must be fed by a 9V ba� ery connected to
the 2-way connector on the side of the control panel. If the main power is cut when
the alarm is on, the auxiliary circuit triggers the siren and locks the vehicle. Cables and
auxiliary batt ery must be purchased separately.
17
LED TRIGGER REPORT
When the alarm is deacti vated aft er going off and the igniti on is turned on, the LED
fl ashes a number of ti mes to indicate what triggered the alarm the last ti me the alarm
was acti vated. If the alarm went off more than once, the LED reports the fi rst trigger.
If you want to see the trigger again, simply turn the igniti on off and on. Another way
to generate this signal is to press the
given for the alarm going off remains valid unti l the alarm is acti vated again. The table
below shows the number of fl ashes the LED gives and the corresponding trigger:
Descripti on
Minimum Sensiti vity
Small Sensiti vity
Average Sensiti vity
Maximum Sensiti vity
bu� on when the alarm is off . The trigger
19
Tabla de contenido
