Black and Decker PRO Serie Manual De Instrucciones página 11

ENGLISH
power tool in unexpected situations.
f. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
g. If devices are provided for the connection of dust extraction and collection facilities, ensure
these are connected and properly used. Use of dust collection can reduce dust-related hazards.
4. Power tool use and care
a. Do not force the power tool. Use the correct power tool for your application. The correct power
tool will do the job better and safer at the rate for which it was designed.
b. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or the battery pack from the power tool before
making any adjustments, changing accessories, or storing power tools. Such preventive safety
measures reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the
power tool or these instructions to operate the power tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts
and any other condition that may affect the power tools operation. If damaged, have the power
tool repaired before use. Many accidents are caused by poorly maintained power tools.
f. Use the power tool, accessories and tool bits etc., in accordance with these instructions, taking
into account the working conditions and the work to be performed. Use of the power tool for
operations different from those intended could result in a hazardous situation.
5. Service
a. Have your power tool serviced by a qualified repair person using only identical replacement
parts. This will ensure that the safety of the power tool is maintained.
6. Electrical Safety
Your tool is double insulated; therefore no earth wire is required. Always check that the main voltage
corresponds to the voltage on the rating plate.
Warning! If the power cord is damaged, it must be replaced by the manufacturer, authorized
Black & Decker Service Center or an equally qualified person in order to avoid damage or injury. If the
power cord is replaced by an equally qualified person, but not authorized by Black & Decker, the
warranty will not be valid.
7. Labels on Tool
The label on your tool may include the following symbols:
Read Instruction Manual
Use Eye Protection
Use Ear Protection
V...............................Volts
A.............................. Amperes
Hz............................ Hertz
W..............................Watts
min...........................minutes
...........................Alternating current
...........................Direct current
n ............................. No load speed
0
...........................Class II Construction
...........................Earthing terminal
...........................Safety alert symbol
.../min...................... Revolutions or reciprocations
per minute
20
ADDITIONAL SAFETY INSTRUCTIONS
FOR ROUTERS
FEATURES
This tool includes some or all of the following features.
1. On/off switch
2. Lock-off button
3. Variable speed control knob
4. Plunge lock lever
5. Spindle lock button
6. Collet
7. Revolver depth stop
8. Chip deflector
9. Depth stop bar
10. Depth of cut scale
11. Dust extraction adaptor
ASSEMBLY
WARNING:
Before assembly, make sure that the tool is switched off and unplugged.
FITTING A ROUTER BIT (FIG. A)
• Remove the chip deflector (8).
• Keep the spindle lock button (5) depressed and rotate the spindle until the spindle lock fully engages.
• Loosen the collet nut (12) using the spanner provided.
• Insert the shank of the router bit (13) into the collet (6). Make sure that the shank protrudes at least 3 mm from
the collet as shown.
• Keep the spindle lock button (5) depressed and tighten the collet nut (12) using the spanner provided.
FITTING THE EDGE GUIDE (FIG. B)
The edge guide helps to guide the tool parallel to an edge.
• Fit the bars (14) to the edge guide (15) using the two screws (16) provided.
• Insert the bars (14) into the router base as shown.
• Set the edge guide to the required distance.
• Tighten the fixing screws (17).
FITTING THE DUST EXTRACTION ADAPTOR (FIG. C)
The dust extraction adaptor allows you to connect a vacuum cleaner to the tool.
• Connect the hose (18) of the vacuum cleaner to the adaptor (11).
FITTING THE TEMPLATE GUIDE (FIG. D) (TEMPLATE GUIDE NOT INCLUDED)
• Fit the template guide (19) to the base of the router, with the flange to the bottom (workpiece) side.
• Insert the two long screws (20) from the bottom side through the template guide and the holes in the base.
• Place a nut onto each of the screws and securely tighten the nuts.
FITTING THE DISTANCE PIECE (FIG. E) (DISTANCE PIECE NOT INCLUDED)
• Fit the distance piece (21) to the base of the router using the screws provided.
ENGLISH
21