Idiomas disponibles
Idiomas disponibles
TROUBLE
SHOOTIHG
PROBLEM
CAUSE
CORRECTION
Trigger valve housing leaks air
O-ringcut er cracked ....................
Replace O-ring
Trigger valve stem leaks air
O-dngiseab cator cracked ................
Replace triggervalve assembly
Frame/nose leaks air
Loosenose screws......................
Tightenand recheck
O-ringor Gasket iscat or cracked ..........
Replace O-ringor gasket
Bumpercrackediwom ....................
Replace bumper
Frame/cap leaks air
Damagedgasketor seal ..................
Replacegasket or seal
Craekediwemheadvalve bumper ...........
Replace bumper
Loosecap screws ......................
Tightenand recheck
Failure to cycle
Air supply restriction .....................
Check airsupply equipment
Tooldry, lack of lubrication ..............
Use BOSTITCHAir ToolLubricant
Worn headvalve O-rings ...............
Replace O-rings
Brokencylinder cap spring ..............
Replace cylindercap spring
Headvalve stuck in cap ................
DisassembWCheck/Lubdcate
Lack of power; slow to cycle
Tooldry, lacks lubrication ...............
Use BOSTITCHAir ToolLubricant
Brokencylinder cap spring ..............
Replace cap spring
O-rings/scab cat or cracked ...............
Replace O-dngs_seab
Exhaustblocked .......................
Check bumper,head valve spring, muffler
Triggerassemblyworn4eaks ..............
Replace triggerassembly
Dirt/tarbuild upon driver .................
Disassemblenose_driver to clean
Cylinder sleeve not seatedcorrectly
onbottom bumper ......................
Disassembleto correct
Headvalve dry .........................
Disassembie4ubricate
Air pressure too low .....................
Check airsupply equipment
Skipping fasteners; intermittent feed
Wornbumper ..........................
Replace bumper
Taddirtin driverchannel ..................
Disassembleand clean noseand driver
Air restriction'inadequateair flowthrough
quickdisconnectsocket and plug ...........
Replacequick disconnectfittings
Wornpiston O-ring ......................
Replace O-ring,check driver
Tooldry, lacks lubrication .................
Use BOSTITCHAir ToolLubricant
Damagedpusher spring ..................
Replace spring
Low air pressure ........................
Check airsupply systemto tool
Loosemagazinenose screws..............
Tightenall screws
Fastenersteo short for tool ................
Useonly recommendedfasteners
Bent fasteners .........................
Discontinueusing these fasteners
Wrongsize fasteners ....................
Useonly recommendedfasteners
Leakinghead cap gasket .................
Tightenscrews_replace gasket
TriggervalveO-ring cut'wom ..............
Replace O-ring
Broken,chippeddriver ....................
Replacedriver (checkpiston O-ring)
Dry,dirtymagazine ......................
Qean4ubdcateuse BOSTITCHAir Tool Lubricant
Worn magazine ........................
Replace magazine
Fasteners jam in tool
Driver channelworn .....................
Replace nose_check door
Wrongsize fasteners ....................
Useonly recommendedfasteners
Bent fasteners .........................
Discontinueusing these fasteners
Loosemagazine/nosescrews..............
Tightenall screws
Broken,chippeddriver ....................
Replacedriver
COIL NAILERS
Skippingfasteners; intermittent feed
/
Fasteners jam intool,canister
Feed piston dry ........................
Add BOSTITCHAir ToolLubricant in hole in feed piston cover
Feed piston O-rings cracked/worn ..........
Replace O-rings/checkbumper and spring. Lubricateassembly.
Check Pawlbinding .....................
Inspect Pawland springon door. Mustwork freely.
Canisterbottom not set correctly ...........
Setcanisterbottom for lengthof nails being used
Brokenweld wires in nail coil ..............
Removecoil of nails and use anothercoil
Wrongsize fastenersfor tool ..............
Useonly recommendedfasteners/check canisterbottomadjustment
Brokenwelded wiresin nailcoil ............
Removecoil of nails and use anothercoil
Wrongslide plate adjustment for
wire/plasticcolbted nailcoil ...............
Adjustswitch pins for wire/plasticcolbted nail coil
-10-
