Ford Connected Charge Station Manual De Instalación página 9

Idiomas disponibles

Idiomas disponibles

1
General information
1.1
Purpose of this document
This document is part of the product and contains
information for electricians to carry out safe installation in
accordance with local regulations, standards, and
requirements.
NOTICE
In addition to this document, follow and comply with
local regulations and standards relating to operation,
installation and environmental protection.
1.2
Using this document
Read this document carefully before installing and
starting the Ford Connected Charge Station.
Keep these instructions ready to hand.
Keep these instructions for future reference.
1.3
Intended use
The Ford Connected Charge Station is designed for
charging electric vehicles in accordance with SAE J1772,
charge Level 2. In this mode, the charge station ensures
that:
– The voltage is not applied before the vehicle has
been properly connected.
– The maximum power is calibrated.
– The AC/DC converter is in the vehicle.
The charge station does not support ventilation,
therefore if the EV requests ventilation, the EVSE (electric
vehicle supply equipment) will not energize the system.
1.4
Use of symbols and highlighting
DANGER
This signal word denotes a hazard with a high degree of
risk which, if not avoided, may result in death or serious
injury.
WARNING
This signal word denotes a hazard with a moderate
degree of risk which, if not avoided, may lead to
minor or moderate injury.
CAUTION
This signal word denotes a hazard with a low degree of
risk which, if not avoided, may result in minor or
moderate injury.
Ford Connected Charge Station Installation Manual
NOTICE
This symbol denotes a special technical feature, or
(if not observed) potential damage to the product.
1.5
Software licenses
This product uses open-source software. Further
information, such as disclaimers, written offers, and
license information, is available through the Ford
Connected Charge Station setup app. See also chapter
6.3, "Displaying soft- ware license information" on page
8.
2
Important Safety Information
2.1
General information
The Ford Connected Charge Station has been developed,
produced, tested, and documented according to the
relevant
safety
regulations
and
requirements that apply to your geographical area.
You must only use the charge station in a technically fault-
less condition. Any malfunctions that adversely affect the
safety of persons or of the device must be immediately
rectified by a qualified electrician in accordance with
applicable regulations and warranty conditions. You are
strictly prohibited from modifying, changing, or
manipulating the device.
NOTICE
Signalling in your vehicle may differ from that
described in this guide. Always read and observe the
vehicle manufacturer's user manual.
SKLJ98-10C823-CA
2.2
General safety information
WARNING
- You must comply with the locally applicable
requirements regarding electrical installations, fire
protection, safety regulations, and escape routes at
the intended installation location.
- Hazardous voltages are present within the casing.
- The Ford Connected Charge Station does not have
its own power ON/OFF switch. The protective devices
in- stalled in the power supply system are therefore
also used to disconnect the power supply.
- Inspect the charge station for visual damage before
installation and use. Do not use the charge station if it
ap- pears to be damaged.
- Installation, electrical connection, and initial
operation of the charge station must be carried out by
a qualified electrician.
environmental
- The screw-mounted unit cover may only be
removed by qualified electricians.
- Do not remove markings, warning symbols, or
the type-label from the charge station.
- The charging cable may only be replaced by
qualified electricians and in accordance with the
installation manual.
- You are strictly prohibited from connecting other
equipment/devices to the charge station than those
for which the charge station was designed and
intended.
WARNING
- When not in use, store the charging cable in the
designated holder and lock the charging coupling in
the remote dock. Loosely wind the charging cable
around the remote dock making sure the cable does
not touch the floor.
- You must make sure that the charging cable and
coupling cannot be driven over, trapped, and are
protected from all other hazards.
1
loading

Este manual también es adecuado para:

Lj98-10c823-ac