Idiomas disponibles
Idiomas disponibles
CAUTION
Do not overtighten the terminal's screws (5 Nm /
44.3 in-lbs max.).
CAUTION
Remove any waste, such as insulation trimmings,
from the connection area.
For rear-facing installations, use an appropriate
cord grip that meets the NEMA 3S standard.
For floor-facing installations of the grid cable, use a
¾"NPT cord grip. (NPT = American National Standard
Pipe Thread standards, also known as national pipe
thread.
5.3.7
Mounting the front cover
1. Use a Torx T20 screwdriver and ten screws (4 x 16 mm
(¼ inch) to tightly mount the front cover (torque set-
ting: 5 Nm / 44.3 in-lbs).
Fig. 13
WARNING
Make sure that the front cover seal is correctly seated
in the sealing groove and has not been damaged. Do
not use the unit if the sealing has been damaged or
has not been fully placed into the groove.
When mounting the front cover onto the housing,
make sure that the HMI ribbon cable is placed fully
inside the enclosure, and that the cable cannot get
pinched be- tween the housing and front cover during
assembly.
5.3.9 Preparing the design cover
If you want a floor-facing cable entry position, then care-
fully break out the correct knock-out segment for cable
entrance in the trim cover using pliers or a similar tool.
For best results, turn the design cover on its back, take a
pair of pliers and place them on the outermost edge, as
shown in the image below, and then press down
carefully. With a round file, smooth any rough edges
after having removed the knock-out.
Ford Connected Charge Station Installation Manual
CAUTION
Wear protective gloves and safety glasses when
breaking out the cable entry area at the predefined
position to avoid injury by edges or burrs.
Fig. 14
5.3.10 Mounting the design cover onto the
housing
Clip the design cover onto the enclosure. When
properly seated, its parts will visibly and audibly snap
on.
Fig. 15
5.3.11 Installing the remote dock
NOTICE
You must mount the dock holder so that the lowest
point of the vehicle connector is between 500 mm
(20 inches) and 1500 mm (60 inches) above floor level
when stored.
NOTICE
You must make sure that the drill holes are at least
95 mm (4 inches) deep.
1. Take the mount dock rear holder out of the box.
2. Mark the drill holes by using the rear part of the
dock holder as a template.
3. Drill two holes (8 mm / 5/16 inch) in the marked
position
4. Push the two dowels (8 x 50 mm / 5/16 x 2 Inches)
firmly into the drill holes.
5. Use a Torx T20 screwdriver and two screws (6 x 90
mm / ¼ x 3.5 inches) to mount the dock's rear
holder on the wall.
Fig. 16
6. Carefully clip the dock front cover onto dock's
rear holder.
Fig. 17
7. To mount the dock-insert onto the dock's front
cover, use two screws (5 x 12 mm / 1/5 x 4.5 inches)
and a Torx T25 screwdriver (torque: 1.8 Nm / 15.9
in-lbs).
Fig. 18
SKLJ98-10C823-CA
5.4
Safety check
Document the results of the checks and measurements
carried out during initial start-up, in accordance with the
applicable installation requirements, and standards. Local
regulations relating to operation, installation, and environ-
mental protection also apply.
DANGER
High voltages.
Danger of fatal electric shock. Danger of confusion
with the drainage holes.
Commissioning the product
6
6.1
Preparing to setup the product
Steps to prepare for commissioning the charge station:
1. Download the FordPass™ app, this will be used to
connect your Ford Connected Charge Station to your
Ford- Pass account.
2. Download the Ford Connected Charge Station Setup
app, this will be used to configure the charge station
to your home Wi-Fi.
3. Locate the Station ID and Access Code on the front of
your charge station or on the front page of the
Operation Manual.
4. Make sure that you have a Wi-Fi signal (for the network that you wa
to run the charge station on) at the charge station location.
6.2
Setting up the product
1. Stand near your charge station and turn on
Bluetooth on your smartphone.
2. Start the FordPass™ app.
3. Select More from the FordPass™ navigation bar.
4. Select Your charge station.
5. Follow the in-app instructions to complete the setup:
6. Select your Station ID from listed charge stations.
7. Enter your Access Code.
8. Locate, and connect to your Wi-Fi network.
7
