Before Starting The Equipment - EINHELL GE-GS 18 Li-Solo Manual De Instrucciones

Danger!
Sound and vibration
Sound and vibration values were measured in
accordance with EN 60745.
L sound pressure level ..................... 73,9 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level ....................... 84,9 dB(A)
WA
K uncertainty ............................................. 3 dB
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 60745.
Vibration emission value a
K uncertainty = 1.5 m/s
The specifi ed vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equip-
ment is used and may exceed the specifi ed value
in exceptional circumstances.
The specifi ed vibration value can be used to
compare the equipment with other electric power
tools.
The specifi ed vibration value can be used for initi-
al assessment of a harmful eff ect.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
Anl_GE_GS_18_Li_SPK7.indb 17 Anl_GE_GS_18_Li_SPK7.indb 17
= 21,251 m/s
2
h
2
- 17 -
GB
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.

5. Before starting the equipment

Warning!
Always remove the battery pack before making
adjustments to the equipment.
5.1 Changing the saw blade (Fig. 3a)
Warning!
Switch off the universal saw and pull out the bat-
tery pack each time before doing any work on the
machine and changing the blade.
Open the cover (Fig. 3a/Item A) by pressing it to-
gether slightly at the front and then swinging it up.
Turn the ring (B) on the blade holder (4) as
shown in Fig. 3a until the blade (6) lets itself be
slipped into the slot of the blade holder (4). When
you now let go of the ring (B) again, the ring (B)
should return to its starting position. If this fails to
happen, try turning the ring (B) by hand into its
starting position.
Now pull on the blade to check whether it is tightly
seated in the holder.
5.2 Fitting the branch jaw clamp (Fig. 3b/3c)
The branch jaw clamp (Fig. 1/Item 5) helps you to
guide the equipment when cutting branches. The
equipment can be used either with or without the
branch jaw clamp.
To fi t the branch jaw clamp, press the lock release
(Fig. 3b/Item A) and push the branch jaw clamp
onto the soleplate from above. Make sure that the
two pins (Fig. 3c/Item A) are correctly seated in
the related recesses (Fig. 3c/Item B) of the so-
leplate. Then check that the branch jaw clamp is
securely seated.
5.3 Charging the Li battery pack (Fig. 4-5)
1. Remove the battery pack (A) from the handle,
pressing the pushlock button (B) downwards
to do so.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(C) into the socket outlet. The green LED will
27.09.2016 11:39:14 27.09.2016 11:39:14