Idiomas disponibles
Idiomas disponibles
Sawing non-ferrous metal
Note: Only use a sharp saw blade that is suitable for non-fer-
rous metal. This guarantees a clean cut and will prevent the
saw blade from jamming.
Switch on the power tool and bring it into contact with the
workpiece, sawing it carefully. Then continue working with
less feed and without interruption.
For profiles, always begin the cut on the narrow side; for U-
shaped profiles, never begin the cut on the open side. Sup-
port long profiles to prevent the saw blade jamming and the
power tool kicking back.
Sawing with a parallel guide (see figure D)
The parallel guide (10) allows you to make precise cuts
along the edge of a workpiece and cut strips with the same
dimensions.
Loosen the wing bolt (8) and slide the scale of the parallel
guide (10) through the guide in the base plate (13). Adjust
the desired cutting width as a scale value at the correspond-
ing (25) or (24) cut mark, see the section "Cut marks".
Retighten the wing bolt (8).
Sawing with an auxiliary guide (see figure E)
For working on large workpieces or for cutting straight
edges, you can securely fasten a board or rail to the work-
piece as an auxiliary guide. The circular saw can be guided
along the path of this auxiliary guide with the base plate.
Maintenance and Servicing
Maintenance and Cleaning
Pull the plug out of the socket before carrying out any
u
work on the power tool.
To ensure safe and efficient operation, always keep
u
the power tool and the ventilation slots clean.
In order to avoid safety hazards, if the power supply cord
needs to be replaced, this must be done by Bosch or by a
customer service centre that is authorised to repair Bosch
power tools.
The retracting blade guard must always be able to move
freely and retract automatically. It is therefore important to
keep the area around the retracting blade guard clean at all
times. Remove dust and chips with a paintbrush.
Non-coated saw blades can be protected against corrosion
using a thin layer of acid-free oil. Remove the oil again before
sawing as failure to do so will stain the wood.
Resin or glue residue on the saw blade has a detrimental ef-
fect on the quality of the cut. You should therefore clean saw
blades straight after use.
After-sales service and advice on using products
Our after-sales service can answer questions concerning
product maintenance and repair, as well as spare parts. You
can find exploded drawings and information on spare parts
at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you
Bosch Power Tools
with any questions about our products and their accessor-
ies.
In all correspondence and spare parts orders, please always
include the 10‑digit article number given on the type plate of
the product.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or ar-
range the collection of a product in need of servicing or re-
pair.
Tel. Service: (0344) 7360109
E-Mail: [email protected]
Ireland
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: (01) 4666700
Fax: (01) 4666888
Australia, New Zealand and Pacific Islands
Robert Bosch Australia Pty. Ltd.
Power Tools
Locked Bag 66
Clayton South VIC 3169
Customer Contact Center
Inside Australia:
Phone: (01300) 307044
Fax: (01300) 307045
Inside New Zealand:
Phone: (0800) 543353
Fax: (0800) 428570
Outside AU and NZ:
Phone: +61 3 95415555
www.bosch-pt.com.au
www.bosch-pt.co.nz
Republic of South Africa
Customer service
Hotline: (011) 6519600
Gauteng – BSC Service Centre
35 Roper Street, New Centre
Johannesburg
Tel.: (011) 4939375
Fax: (011) 4930126
E-mail: [email protected]
KZN – BSC Service Centre
Unit E, Almar Centre
143 Crompton Street
Pinetown
Tel.: (031) 7012120
English | 17
1 609 92A 4MR | (26.09.2018)
