LEGRAND Wattstopper DW-311-W Instrucciones De Instalación

No: 26167 – 10/21 rev. 7
Catalog Numbers • Les Numéros de Catalogue • Números de Catálogo: DW-311/DW-311-347
Country of Origin: Made in China • Pays d'origine: Fabriqué en Chine • País de origen: Hecho en China
Models ending in -U are BAA and TAA compliant (Product produced in the U.S.)
DESCRIPTION AND OPERATION
The DW Dual Technology Multi-Way Wall
Switch sensors combine advanced passive
infrared (PIR) and ultrasonic technologies
into one unit. The combined technologies
help to eliminate false triggering even in
difficult applications.
• The DW sensor has Multi-Way available
on all models.
• A "walk-through" mode can turn lights
off after only 3 minutes, if no activity is
detected after 30 seconds following an
occupancy detection.
• The DW-311 has one relay with dimming
control capability and two buttons to
allow control of the dimming.
• DW sensors contain a light level sensor. If adequate daylight
is present, the sensor holds the load OFF until light levels
drop, even if the area is occupied. See the Light Level
Adjustment section.
• On loss of normal power to the DW-311, the 0-10V dimming
control will open. Any light fed with a separate circuit but
controlled by the unit's 0-10V signal will go to 100%.
1. Make sure that the power has been turned OFF at the circuit breaker.
2. Connect wires to the DW flying leads as shown in the wiring diagram that
is appropriate to the DW model and electrical supply. The ground wire
(green) must be fastened to ground for the sensor to work properly.
3. Attach the sensor to the wall box by inserting screws into the two wide
holes on the top and bottom of the attached metal bracket. Match them up with the
holes in the wall box and tighten. Do not use excessive force when installing
the sensor into the wallbox. Doing so can bend the mounting strap which can
affect button operation.
4. Turn the circuit breaker ON. Wait one minute, then push the Auto ON/OFF switch
and the lights will turn ON. There is a delay due to initial power-up of the sensor
that only occurs during installation.
5. Test and adjust the sensor if necessary.
6. Install industry standard decorator wall switch cover plate (not included).
WARNING: Grounding the purple and pink wires can damage the unit. Do not apply
power to the sensor until all wires are connected or capped off if the driver is to be
installed at a future time.
8" flying leads for
line, load, ground
and multi-way
connections
Red
White
Black
Wattstopper
Dual Technology 0–10 Volt Wall Switch Occupancy Sensor (version 2)
Interrupteur mural 0–10 Volt avec détecteur de mouvement à double technologie (v2)
Sensor de ocupación con interruptor de pared y tecnología doble de voltaje 0 a 10 (V2)
Installation Instructions • Instructions d'Installation • Instrucciones de Instalación
INSTALLATION
#12 – #14 AWG
Strip Gauge
Pink
Purple
1/2"
12.7mm
Cu Wire Only
Yellow
NOTE: Per UL, the 0-10V negative dimming
wire color has been changed from gray to pink.
Green
®
SPECIFICATIONS
Voltages:
DW-311 .................................................120/277 VAC, 50/60 Hz
DW-311-347 .................................................347 VAC, 50/60 Hz
Load Limits:
@120 VAC......... 1000-W tungsten ballast, E-ballast, LED, 1/4 HP
@277 VAC ................... 1200-W ballast, E-ballast, LED, 1/4 HP
@347 VAC .....................................1500W ballast, LED, 1/4 HP
Time Delay Adjustment ..................................................3 to 30 minutes
Walk-Through Mode ....................... 3 minutes if no activity after 30 sec.
Test Mode ............................................. 10 min. with 10-sec. time delay
PIR Adjustment .................................................................... High or Low
Ultrasonic Adjustment ..................... Minimum to Maximum (trimpot), Off
Alerts ........................................................Selectable Audible & Visual
Multi-Way Capability ...............................................................All models
Terminal screw torque ............................................ 16 lbf-in (18 kgf-cm)
High Trim ................................................................................... 6 to 10V
Low Trim ...................................................................................... 0 to 4V
Ramp Up ....................................................................... 1 to 10 seconds
Fade Down ................................................................. 2.5 to 30 seconds
Complementary Listed to "Emergency Lighting Equipment", (UL924)
WARNING: TURN THE POWER OFF AT
THE CIRCUIT BREAKER BEFORE WIRING.
DW-311 and DW-311-347 Wiring
Line
Ground
Neutral
0-10V
Dimming
Yellow Purple
Pink
Black Red
Green
White
Driver
or Ballast