Craftsman PRO G8200 Manual Del Operador página 17

Idiomas disponibles

Idiomas disponibles

Engaging the PTO (Manual PTO tractors)
Engaging the PTO transfers power to the cutting deck or other (separately available)
attachments. To engage the PTO:
1.
Move the throttle to the FAST
2.
Push the PTO handle forward into the engaged (ON) position. See "Figure
14".
NOTE: When operating the tractor be certain that the throttle is always in
the FAST
position. Operating with the throttle at less than full throttle
may lead to premature battery wear and a poor quality cut.
To disengage the PTO, pull the PTO handle rearward into the disengaged (OFF)
position.
Mowing
Make certain the area to be mowed is free of debris, sticks, stones, wire or
other objects that can be thrown by the rotating blades.
NOTE: Do not engage the mower deck when lowered in grass. Premature wear and
possible failure of the belt and PTO clutch will result. Fully raise the deck or move to
a non-grassy area before engaging the mower deck.
1.
Mow up and down slopes, not across.
2.
Avoid turns when driving on a slope. If a turn must be made, turn down the
slope. Turning up a slope greatly increases the chance of a roll over.
3.
Avoid stopping when driving up a slope. If it is necessary to stop while
driving up a slope, start up the slope smoothly and carefully to reduce the
possibility of flipping the tractor over backward
4.
Place the throttle into the FAST
5.
Lower the mower deck to the desired height setting using the deck lift handle.
6.
Slowly press the forward drive pedal with your right foot until the desired
speed is achieved.
NOTE: The speed of the tractor will affect the quality of the mower cut.
Mowing at full speed will adversely affect the cut quality. Control the ground
position.
Figure 14
WARNING
position and engage the PTO.
OPERATION
speed with forward drive pedal.
7.
When approaching the other end of the strip, slow down or stop before turning.
8.
Align the mower with an edge of the mowed strip and overlap approximately 3".
9.
Direct the tractor on each subsequent strip to align with a previously cut strip.
10.
To prevent rutting or grooving of the turf, if possible, change the direction
that the strips are mowed by approximately 45° for the next and each
subsequent mowing.
Be careful when crossing gravel paths or driveways. Disengage the PTO and
raise the deck to the highest position before crossing.
NOTE: When stopping the tractor for any reason while on a grass surface,
always:
Make sure the drive pedal is in neutral.
Engage the parking brake.
Shut the engine off and remove the key.
Doing so will minimize the possibility of having your lawn
''browned'' by hot exhaust from your tractor's running engine.
Using the Differential Lock (if equipped)
When the differential lock is on, be sure to allow for a larger turning radius
and greater steering effort.
Engage the differential lock only when the vehicle is stationary. Do not use
the differential lock when traveling downhill.
NOTE: The system should only be used when poor traction is encountered. It should
be disengaged when traveling on surfaces with adequate traction.
In some instances, the tractor may be driven in slippery or low-traction situations
and it may be necessary to activate the differential lock. To use the differential lock
proceed as follows.
1.
Press down on the brake pedal to stop the motion of the tractor.
2.
Press down on the differential lock pedal to engage the differential lock.
NOTE: The differential lock only works while the pedal is pressed.
3.
Release the brake pedal to drive the tractor forward while differential lock is
engaged.
NOTE: Engagement may be delayed. The differential lock will engage when
different wheel speeds are detected.
NOTE: Disengagement may be delayed. The differential lock will disengage
when the rear wheel speeds allow it to release.
4.
To disengage the differential lock, release the differential lock pedal.
17
WARNING
WARNING
WARNING
loading