Idiomas disponibles
Idiomas disponibles
The electronic speed adjustment allows you to work at
the ideal speed for each abrasive and surface type. This
is particularly useful for sanding heat-sensitive materials
which require lower sanding speeds.
ROTARYORBITAL SANDER: The single-handed rotar-
yorbital sander combines two types of movement, one
rotational and the other orbital, enabling it to perform
planing and finish work very quickly. The smooth, sanded,
groove-free surfaces produced make it ideal for delicate
jobs and varnished wood.
Equipped with forced suctioning of sanding dust. The
sander LRB384 is factory equipped with a velcro base
plate 8445498, which enables it to be converted into a
rotaryorbital sander.
Equipped with electronic speed adjustment devices
which allow you to work at the ideal speed for each
surface and abrasive type. This is particularly useful for
sanding heat-sensitive materials which require lower
sanding speeds.
4. STANDARD EQUIPMENT
Inside the box you will find the following:
- Allen service key e/c: 4 mm.
- Mobile base sander set with Velcro delta pad 8445498
- Velcro rotaryorbital base
- Mobile base
- Suction bag set
- Instruction manual and other documentation
- 1 abrasive sheet for mobile base
- 3 Velcro abrasive sheets for Delta base
- 1 Velcro abrasive disk
- 1 Velcro adaptor
5. OPTIONALS ACCESORIOS
- Velcro mobile base Ref. 8445189
- Centring and abrasive drilling device 8445232
- Delta mobile base Ref 8445052
- Velcro adaptor Ref 8445053
- Standard dust collection attachment 6446073 2.25 m
- Standard dust collection attachment 1746245 5 m
6. SPECIFICATIONS OF THE TOOL
Brushless motor
Power tool equipped with a brushless motor that pro-
vides the following advantages (compared to the power
tool having a brush motor):
• High reliability due to the lack of wearing parts (car-
bon brushes, commutator).
• Increased operating time on a single charge.
• Compact design and light weight.
Temperature protection
The temperature protection system enables to auto-
matically deactivate the power tool in case of excess
load or when the temperature of the battery 7 (Fig. 10)
is exceeding 70°C. The system guarantees protection of
the power tool from damage in case of noncompliance
with the operation conditions.
Overdischarge protection
The battery 7 (Fig. 10) is protected by the safety system
against deep discharge. In case of complete discharge,
the power tool is automatically switched off.
Do not try to switch on the power tool
when the protection system is activated
the battery 7 (Fig. 10) can be damaged.
Indicators of the state of battery charge (Fig. 13)
With the push of the button 6 the indicators 5 show
the state of charge of the battery 7.
Overheating protection
Overheating protection system of the engine automati-
cally switches off the power tool in case of overheating.
In this situation, let the tool cool before turning the
power tool on again.
Overload protection
Overload protection system of the engine automatically
switches off the power tool when it is operated in a man-
ner that causes it to draw an abnormally high current.
Soft start
Soft start enables smooth start of power tools - is
being run up gradually with no jerks and kickbacks; no
jump-like load is imposed on the motor upon switching.
LED light
By pressing the on/off switch B, the LED light N (Fig.1)
turns on automatically and allows you to perform tasks
in low light conditions.
7. HOW TO CHARGE THE BATTERY
Battery charging time
Initial operating of the power tool
Before the first use, the battery 7 (Fig. 10) must be
fully charged.
Charging process (Fig. 11)
• Press the battery lock 4 and remove the battery 7
(Fig. 10).
• Connect the charger 19 to the power supply.
• Insert battery 7 into charger 19 (Fig. 11).
• Disconnect the charger 19 from power supply after
13
