Idiomas disponibles
Idiomas disponibles
1.3 SAFETY INSTRUCTIONS FOR USE AND MAIN-
TENANCE OF THE BATTERY AND CHARGER
Do not store the tool and battery cartridge
in locations where the temperature may
reach or exceed 45° C.
Do not incinerate the battery cartridge.
Do not expose battery cartridge to water
or rain.
• Only recharge with the manufacturer's specified
charger. Only recharge with the manufacturer's specified
charger. A charger which is suitable for one type of
battery cartridge can cause a fire risk on another type
of battery cartridge.
• Only use this power tool with the battery cartridge
specifically designed for this model. The use of other
types of battery cartridges may cause injury to the
operator and a fire risk.
• When the battery cartridge is not in use, keep it away
from metal objects, such as paper clips, coins, keys, nails,
screws or other small metal objects that can establish
contact from one terminal to the other. Shorting the
battery terminals may cause burns or a fire.
• Battery fluid may be spilled under extreme conditions;
avoid contact with this liquid. In case of accidental
contact, rinse thoroughly with water. If the liquid comes
into contact with your eyes, seek medical attention.
Battery fluid may cause irritation or burns.
• Do not use damaged or modified batteries. Damaged
or modified batteries can behave in an unpredictable
way and may cause injury to the operator and a fire risk.
• Avoid switching the device on accidentally. Make sure
the on/off switch is in the off position before inserting
the battery. Carrying the power tool with your finger
on the on/off switch or inserting the battery with the
switch in the on position can cause accidents.
• Do not open the batteries. You could damage the
circuits.
• Fumes may be aired if there is battery damage and
improper use. In this case, go to a well-ventilated location
and seek medical assistance, if necessary. Fumes cause
respiratory irritation.
• When the battery is defective, the liquid may leak and
come into contact with adjacent components. Check the
corresponding parts. Clean or replace them, if necessary.
• Protect the battery from heat, continued solar radiation
and fire. There is an explosion hazard.
12
Read all instructions and safety warnings.
• Protect the battery charger from rain and moisture.
Water entering the charger increases the risk of electric
shock.
• Do not charge other batteries. The battery charger is
only suitable for charging lithium-ion batteries within
the indicated voltage range. Otherwise, there is a fire
and explosion hazard.
• Keep the battery charger clean. Dirt can cause a risk
of electric shock.
• Always check the battery charger, its cable and plug
before using them. Do not use the charger if you see it
is damaged. Do not open the charger on your own. Have
it repaired by a qualified person who uses original spare
parts. Damaged chargers, cables and plugs increase the
risk of electric shocks.
• Do not use the battery charger on highly flammable
surfaces. For example, paper, textiles, etc., or in
combustible environments. A fire hazard exists from the
charger heating during the charging cycle.
2. SPECIFICATIONS
Battery voltage..........................................................20 V
No-load speed....................................4.800 - 10.000 min
Battery type....................................................................Li-Ion
Time to charge battery................................................60 min
Battery capacity.........................................................2 or 4 A
Orbit diameter....................................................................2 mm
Sanding surface.....................130x80 mm (Sanding pad)
Abrasive disk diameter...................125 mm (Abrasive disk)
Weight..................................................................................1.3 kg
Weighted equivalent continuous acoustic
pressure level A...........................................................77 dBA
Incertidumbre de la medición............................K = 3 dBA
Wear ear protection!
Vibration total values.........................................a
Uncertainty..........................................................K: 1,5 m/s
3. USES
ORBITAL SANDING MACHINE: A single-handed sander for
dry surface finishing. Equipped with forced suctioning
of sanding dust.
To obtain a good quality finish, slide the machine over the
surface to be worked in repetitive elliptical movements
to avoid the formation of grooves on the sanded surface.
To achieve the desired finish, the surface should be sanded
several times using a finer grain of abrasive each time.
With the delta base 8445198 included with the machine,
even difficult to reach inside corners and slatted shutter
can easily be sanded.
-1
h
: 2,5 m/s
2
h
2
