Idiomas disponibles
Idiomas disponibles
7.5
Transport
For transport, turn the lever (5) all the way down and
stop by actuating the transportation lock (4).
Note: To lock the lever, it is necessary to turn the
cutting depth limiter (3) to a lower position. See
section 7.1.
8. Maintenance
Disconnect the mains plug before starting
any conversion or maintenance work!
Engage the spindle locking knob (8) only
when the motor is inoperative.
8
Removing the cutting disc:
- Press lever for spindle locking knob (8) to the right
and turn the cutting disc by hand until the spindle
locking knob is felt to engage.
- Use the wrench (c) to remove the screw with
clamping flange (b) anti-clockwise.
- Remove cutting disc.
Fitting the cutting disc:
- Put on new cutting disc (a).
- Fit the screw with clamping flange (b).
- Use wrench (c) to lock spindle and tighten screw
with clamping flange (b).
- Check whether the spindle locking knob (8) is
completely disengaged again.
- Clean the dirty machine and remove the grinding
dust.
Regular maintenance:
Oil the following parts at least once a month:
movable parts of the vice.
9. Troubleshooting
CS 22-355: Switching on procedures produce brief
reductions in voltage. Unfavourable power
conditions can be detrimental to other devices.
Power impedances smaller than 0.24 ohm should
not cause any malfunction.
10. Accessories
Use only genuine Metabo accessories.
If you need any accessories, check with your
dealer.
For dealers to select the correct accessory, they
need to know the exact model designation of your
power tool.
See page 3.
A Cutting discs: Quality class A 36-R
"Flexiamant Super" inox.
a
b
c
Special cutting disc of medium hardness for
stainless steel.
High cutting performance with long lifetime.
B Cutting discs: Quality class A 30-R / A 36-S
"Flexiamant Super" steel.
Good cutting performance in steel, with good
lifetime.
Hard version for powerful machines.
A 36-S: with an interior fabric for quick cuts.
C Cutting discs: Quality class A 24-M
"Flexiamant Super" steel.
High cutting performance in steel, with good
lifetime.
Soft version for less powerful machines.
For a complete range of accessories, see
www.metabo.com or the main catalogue.
11. Repairs
Repairs to electrical tools must be carried out
by qualified electricians ONLY!
A defective mains cable must only be replaced with
a special, original mains cable from metabo, which
is available only from the Metabo service.
If you have Metabo electrical tools that require
repairs, please contact your Metabo service centre.
For addresses see www.metabo.com.
You can download spare parts lists from
www.metabo.com.
12. Environmental Protection
The generated grinding dust may contain harmful
substances. Dispose appropriately.
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
Only for EU countries: Never dispose of
power tools in your household waste! In
accordance with European Directive 2012/
19/EU on waste electrical and electronic equipment
and its implementation in national law, used elec-
trical tools must be collected separately and
handed in for environmentally compatible recycling.
13. Technical Specifications
Explanatory notes on the specifications on page 3.
Changes due to technological progress reserved.
U
=Voltage
I
= Current
P
=Rated input
1
P
=Power output
2
n
=No load speed
0
Cutting disc dimensions:
D
=Maximum outer diameter
max
B
=Wheel thickness
d
=Bore
H
=max. cutting diameter 90°
max 90°
H
=max. cutting diameter 45°
max 45°
L
=Max. vice opening
max
m
=Weight without mains cable
ENGLISH en
15
