Bühler technologies Multitronik Guía Rápida página 12

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 19
Multitronik
9 Menu Sequence Overview
Main menu
Submenu 1
Configuration
M__i
Shortcut
or 60s no action:
Equipment configuration
Exit main/submenu
____
Display
____
Measurement display
____
Out 1
Multitronik
Mult
Multitronik main menu
Settings menu OUT1
Out x
Settings menu OUTx
Analog Out1
Settings menu Analog 1
Exit
Exit menu level
b. E F
Reset
Basic EF
Basic Adv. Functions
Factory setting
Set error handling
Error handling
Set Unit Multi
Multitronik unit
Set Upper
Assignment 20 mA
reassign O1
Set Out 1
reassign O2
Set Out 2
Set Lower
Assignment 4 mA
Display Rate
Display rate
Lock Device
Keylock
Exit
Exit menu level
Diagnostic
diA
Journal Out
Diagnostics menu
Log output
Max/Min Multi
Max/Min memory
Set Journal Out
Output monitoring
Delay MM
Min/Max Delay
Exit
Exit menu level
E
Exit
Exit menu level
12
Bühler Technologies GmbH
Submenu 2
Submenu 3
+
out1
____
SP1
____
____
FH1
F1. H i
Switching point 1
rP1
____
FL1
F1. L o
____
Switch-back point 1
____
EF1
EF 1
Delay SP 1
Extended functions
Delay OUT1 On
Delay RP 1
Delay OUT1 Off
Set Out 1
Definition OUT1
Check Out 1
Functional test OUT1
LED Out 1
Function status LED1
Exit
Exit menu level
____
Exit
E
Exit menu level
____
See menu structure Out1
out_
Not applicable for version with
analogue output
____
____
An1
Analog Max1
A1. H i
Set maximum value
____
Analog Min1
A1. L o
Set minimum value
____
Set A.Out1
A. o u1
Output function
____
Check An1
C. A n1
Functional test Analog 1
____
Exit
E
Exit menu level
E
rES
Errh
M. u ni
M. H i
r. o u 1
r. o u 2
M. L o
di5
Loc
E
J. o ut
M. M M
SJ. o u
DM. M M
E
Settings and Display Menu
Change measurement display to show details for the unit:
____
Switch
____
°C °F mbar bAr MPA PSi-I- cm in Lit CAL non non1 non2
Display unit
mbar
available when max. pressure (P.Hi) <=10 bar
____
Selection menu
____
SP1
Setting the switching point /
FI. H i
< m. L o - M. H i >
Sets a value for frequency 100 Hz (OUT1 and OUT2 only)
____
Selection menu
Set switch-back point /
____
rP1
FI. L o
Sets a value for frequency 1 Hz (only OUT1 and OUT2)
< m. L o - M. H i >
dS1
____
Selection menu
____
___
Amount of time the signal must be present for output OUT1 to trigger.
0 - 100
Setting range: 0...100 seconds (for frequency output without function)
____
____
dr1
Selection menu
___
Amount of time the signal must be present for output OUT1 to switch back.
0 - 100
Setting range: 0...100 seconds (for frequency output without function)
Definition of switching characteristics for output 1:
____
Selection menu
____
ou1
___
Hno Hnc Hysteresis function NO contact or NC contact
Hno - FM
Fno Fnc Window function NO contact or NC contact /
n. o P
Normal switching output operation
____
____
C. o u1
Selection menu
____
oFF
Switching output Off /
n. o p - on
on
Switching output On /
____
____
LEd1
Selection menu
L=__
LED = output: follows switching output
L= o
L= o - L=-o
L=-o
LED = -output: inverted to switching output
____
E
____
Selection menu
____
Sets the maximum analogue output signal to a defined value.
(Note: Max. – Min >= 10 % of the measuring range)
< m. L o - M. H i >
____
Selection menu
____
Sets the maximum analogue output signal to a defined value.
(Note: Max. – Min >= 10 % of the measuring range)
< m. L o - M. H i >
____
Selection menu
_ _
Selecting the analogue output function:
i I
4...20 mA
i 1 - u 3
____
Selection menu
____
Analogue output normal mode /
n. o P
n. o P - Lo
HALF
Output mean analogue value /
Alternate menu for version with analogue output
Not applicable when ordered with 2 or more
switching outputs
Confirm
____
___
Resets the device to delivery status
no - YES
____
Selection menu
___
Disable/enable normal error handling and analysis
; n o - Yes
C [Celsius], F [Fahrenheit],
____
Selection menu
___
-I- [pecent], cm [centimetre], in [inch], Lit [litre], CAL [Gallon],
°C - non2
non, non1, non2
____
Selection menu
____
Configures the maximum measurement range for the connected sensor.
-999 - 9999
(Example: sensor maximum measuring range 100 bar, corresponds to 20 mA)
____
Selection menu
____
Set switching output Out 1 to function or to error signal
Err - Multi
____
Selection menu
____
Set switching output Out 2 to function or to error signal
Err - Multi
____
Selection menu
____
Configures the minimum measuring range for the connected sensor.
(Example: sensor maximum measuring range 0 bar, corresponds to 4 mA)
-999 - 9999
____
Selection menu
___
Selecting the display refresh rate:
Fast - off
FASt [fast], Medi [medium], SLo [slow],
____
Selection menu
___
Activating the keylock by entering a numerical code > 0 Master code 287
0 - 999
____
Selection menu
____
Displays the last 6 alarms + delete function.
Display:
JorX
Jor I - ---
____
Selection menu
____
Displays limits + delete function.
____ - ---
Display: Value – time passed in hours/days; toggle values and time ▲▼
____
Selection menu
out_
Selecting the alarm output to be logged
Out1 - Out_
____
Selection menu
___
Amount of time the signal must be present before saving the maximum / minimum
value. Setting range: 0...100 seconds
0 - 100
FH1 Define maximum window limit
FL1 Set lower window limit
Frequency output 1-100 Hz
FM
F1
Simulation 1 Hz
F100
Simulation 100 Hz
u 1
2...10 V
u 2 0...10 V
u 3 0...5 V
Hi Output maximum analogue value
Lo Minimum analogue value output
nbar
[mbar],
bAr [bar],
MPA
[Mega Pascal], PSi [psi],
[no unit]
oFF [Display off]
X – time passed in hours/days; toggle alarms ▲▼
BX140014 ◦ 12/2019E
loading