Idiomas disponibles
Idiomas disponibles
5. Use protective clothes.
6. Protect against humidity.
7. Do not allow other persons to stay in the operation range
8. Protection class 2
9. Do not put your extremities close – liquid under high pressure!
10. Keep children away
CONSTRUCTION AND USE
High pressure cleaner is a 2 protection class device designed for
cleaning surfaces with high pressure water stream. High pressure
cleaner is widely used in households, transport, building industry,
agriculture and other fields. It is especially useful for cleaning cars,
trailers, buildings, ceramic tiles etc.
Use the device according to its purpose only.
DESCRIPTION OF DRAWING PAGES
Below enumeration refers to the device elements depicted on the
drawing pages of this manual.
1. Transport handle
2. Water outlet connector
3. Water inlet connector
4. Wheel
5. Switch
a. Lance
b. Gun handle
c. Pressure hose
d. Trigger lock button
e. Trigger
f. Nozzle
g. Water inlet connector
h. Detergent container
i. Spraying tip
* Differences may appear between the product and drawing.
MEANING OF SYMBOLS
CAUTION
WARNING
ASSEMBLY/SETTINGS
INFORMATION
EQUIPMENT AND ACCESSORIES
1. Pressure hose
2. Gun handle
3. Lance (2 pieces)
4. Water inlet connector
5. Transport handle
6. Screws
PREPARATION FOR OPERATION
LANCE AND GUN HANDLE ASSEMBLY / DISASSEMBLY
• Connect two parts of the lance (a) by pressing them slightly
(observe the notch in the joint) and turning one part by 15
another (fig. A).
• Use the same method to join the lance (a) with the gun handle (b).
• Disassemble the lance in reverse order.
PRESSURE HOSE AND WATER SYSTEM ASSEMBLY
Filter placed in the water inlet should always be installed to filter
out sand, limestone and other contaminations that could damage
valves in the cleaner pump.
• Screw the high pressure hose connection (c) onto threaded inlet in
• Screw the other end of the pressure hose (c) onto water outlet
• Install connection of the water inlet (g) on the water inlet connector
• Use the trigger lock button (d) to lock the trigger (e) of the gun
• Connect water supply hose to water inlet connector (g) (water
• Connect the water supply hose to a water valve.
• Switch on the water supply, ensure the water supply valve is fully
Water temperature on the inlet connector must not be higher
than 40
working pressure 3 bar or higher, inner diameter 13 mm (1/2").
Water should be clean and free from sand and corrosive substances.
Dry operation (without water) will damage the device.
Press the trigger of the gun handle before starting operation to
remove air from the pump and pressuer hose.
WATER STREAM ADJUSTMENT
Nozzle enables stream adjustment from very narrow to wide.
• Take the lance (a) body with one hand.
• Turn the nozzle (f) with the other hand (turn left or right) until
Use narrow stream to clean small and very dirty surfaces (very high
water pressure). Use wide stream to clean large, slightly dirty surfaces
(high water pressure).
INSTALLATION OF TRANSPORT HANDLE
You can transport the high pressure cleaner to a workplace by rolling
on its wheels. Use transport handle with convenient hook for power
cord and pressure hose.
• Install transport handle (1) in the rear part of the device casing,
- 1 pce
- 1 pce
IMMEDIATE HALT SYSTEM
- 1 pce
- 1 pce
- 1 pce
- 1 set
High pressure cleaner is equipped with immediate halt system
that is motor protection. When the gun handle trigger is released
the motor halts.
Pressing the trigger again will start the motor again.
SWITCHING ON / SWITCHING OFF
0
against
When using the cleaner it is recommended to hold the gun handle
with one hand and the lance with the other. Using two hands to
hold protects against uncontrolled recoil of the lance when
starting up and during operation.
The mains voltage must match the voltage on the rating plate of
the high pressure cleaner.
10
the gun handle (b) (fig. B).
connector (2) (fig. C).
(3) (fig. E).
handle (b) (fig. D).
supply hose is not included).
opened.
0
C. Water supply hose parameters should be as follows:
required stream is set (fig. F).
tighten screws (included) to secure in place.
OPERATION / SETTINGS
