Idiomas disponibles
Idiomas disponibles
• Do not operate chainsaw while in a
tree, on a ladder, on a scaffold, or
from any unstable surface.
• Hold tool by insulated gripping
surfaces when performing an
operation where the cutting tool may
contact hidden wiring. Contact with a
"live" wire will make exposed metal parts
of the tool "live" and shock the operator.
• Do not attempt operations beyond
your capacity or experience. Read
thoroughly and understand completely all
instructions in this manual.
• Before you start chainsaw, make sure
saw chain is not contacting any object.
• Do not operate a chainsaw with one
hand! Serious injury to the operator,
helpers, or bystanders may result from
one handed operation. A chainsaw is
intended for two-handed use only.
• Keep the handles dry, clean, and free
of oil or grease.
• Do not allow dirt, debris, or sawdust
to build up on the motor or outside
air vents.
• Stop the chainsaw before setting
it down.
• Do not cut vines and/or small
under brush.
• Use extreme caution when cutting
small size brush and saplings because
slender material may catch the saw chain
and be whipped toward you or pull you
off balance.
WARNING:
power sanding, sawing, grinding, drilling,
and other construction activities contains
chemicals known to the State of California
to cause cancer, birth defects or other
reproductive harm. Some examples of these
chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and
cement and other masonry products,
and
• arsenic and chromium from
chemically-treated lumber.
Your risk from these exposures varies,
depending on how often you do this type
of work. To reduce your exposure to these
chemicals: work in a well ventilated area,
and work with approved safety equipment,
such as those dust masks that are specially
designed to filter out microscopic particles.
• Avoid prolonged contact with dust
from power sanding, sawing, grinding,
drilling, and other construction
activities. Wear protective clothing
and wash exposed areas with soap
and water. Allowing dust to get into
your mouth, eyes, or lay on the skin may
promote absorption of harmful chemicals.
WARNING:
generate and/or disburse dust, which
may cause serious and permanent
respiratory or other injury. Always use
Some dust created by
Use of this tool can
NIOSH/OSHA approved respiratory
protection appropriate for the dust
exposure. Direct particles away from face
and body.
An extension cord must have adequate
wire size (AWG or American Wire Gauge)
Minimum Gauge for Cord Sets
Volts
Total Length of Cord in Feet
120V
0-25
240V
0-50
Ampere Rating
More Not more
Than Than
0
-
6
18
6
-
10
18
10 -
12
16
12 -
16
14
for safety. The smaller the gauge number
of the wire, the greater the capacity of the
cable, that is 16 gauge has more capacity
than 18 gauge. When using more than one
extension to make up the total length, be
sure each individual extension contains at
least the minimum wire size.
Recommended Minimum Wire Size for
Extension Cords
CHAINSAW NAMES AND TERMS
• Bucking - The process of cross cutting a
felled tree or log into lengths.
• Motor - A device used to stop the saw
chain when the trigger is released.
• Chainsaw Powerhead - A chainsaw
without the saw chain and guide bar.
• Drive Sprocket or Sprocket - The
toothed part that drives the saw chain.
• Felling - The process of cutting down a
tree.
• Felling Back Cut - The final cut in a tree
felling operation made on the opposite
side of the tree from the notching cut.
• Front Handle - The support handle located
at or toward the front of the chainsaw.
• Front Hand Guard - A structural barrier
between the front handle of a chain saw
and the guide bar, typically located close
to the hand position on the front handle.
• Guide Bar - A solid railed structure that
supports and guides the saw chain.
• Guide Bar Scabbard - Enclosure fitted
over guide bar to prevent tooth contact
when saw is not in use.
• Kickback - The backward or upward
motion, or both of the guide bar occurring
when the saw chain near the nose of the
top area of the guide bar contacts any
object such as a log or branch, or when
the wood closes in and pinches the saw
chain in the cut.
• Kickback, Pinch - The rapid pushback of
the saw which can occur when the wood
closes in and pinches the moving saw chain
in the cut along the top of the guide bar.
5
26-50
51-100 101-150
51-100 101-200 201-300
American Wire Gauge
16
16
16
14
16
14
12
Not Recommended
14
12
12
