Dimplex CAS1000M Manual página 7

by pressing the button on Button Panel 'A', the LED's will start to blink on and off. This is to let you know that the
appliance is ready to connect to the remote control. Press the
off. Now the remote control is paired to the appliance.
The operation of the remote control is the same as described in 'Receiver Controls'. You can pair multiple products to
the one remote control by repeating the pairing operation as above on your subsequent products.
The operation of the remote control is the same as described in 'Bluetooth Receiver Controls'.
Pairing to multiple products: If you are installing multiple CAS500/CAS1000 products you can pair them to one remote
control. To do this, please install the products as described in the "Installation Instructions". Please ensure that the
products are connected to mains power and have water supplied. If you are pairing CAS1000 and CAS500 products
please choose the 6 button remote control as the master remote control. Pair the fi rst product as described in the
'REMOTE CONTROL' section above
1. On your second product press the rocker switch to the on (I) position, 1 beep
2. Press on the manual controls, 1 beep and the product will begin to start.
3. Press on the manual controls, beep and LED's start to blink.
4. Press on the remote control. The product will beep and LED's fl ash 5 times.
The product will automatically switch off.
5. Repeat the above steps to pair the next product.
When all products are paired, test the remote control by pressing (standby). If any of the products fail to receive a signal
from the remote control you can bring that product back in line with the others via the Manual Controls or the receiver
controls.
Maintenance
GENERAL TIPS
Only use fi ltered tap water in this appliance.
Always ensure that the appliance is sitting on a level surface.
If you intend not using the appliance for longer than 2 weeks, remove and empty the sump and water tank.
Once installed, never move this appliance or lay on its back, without draining the water from sump and water tank.
CLEANING
Warning – Always press Switch 'A' to the 'OFF' (0) position (Fig.10) and disconnect from the power supply before clean-
ing the fi re.
We recommend cleaning the following components once every 2 weeks, particularly in hard water areas:-
Water Tank, Sump, Nozzle, Tank cap and seal, Air fi lter.
For general cleaning use a soft clean duster – never use abrasive cleaners. To remove any accumulation of dust or fl uff the soft brush attachment of a vacuum cleaner should occasionally be used
to clean the outlet grille of the fan heater.
Water tank
1. Remove water tank, as described earlier, put into sink and empty water.
2. Using the supplied brush gently rub the inside surfaces of the cap paying particular attention to the rubber ring in
the outer groove and the centre rubber seal.
3. Put a small quantity of washing up liquid into the tank, refi t the cap and shake well, rinse out until all traces of washing
up liquid are gone.
4. Refi ll with fi ltered tap water only, replace the cap, do not overtighten.
Sump
1. Press Switch 'A' to the 'OFF' (0) position
2. Gently lift out the fuelbed and place carefully on the ground.
3. Remove the water tank by lifting upwards.
4. Disconnect the electrical connector, located on the right side of the sump. (Fig.5) .
5. Release the right sump locking tabs by turning 90º. This allows the sump to be lifted completely from its location. (Fig.
11)
6. Gently lift up the sump, taking care to keep level so as not to spill any water. Sit the assembly in the sink.
7. Release the left sump locking tabs by turning 90º, then lift off the Nozzle. (Fig.3)
8. Lift out the transducer and carefully tilt, as shown, so that the liquid drains out of the sump. (Fig.13)
9. Put a small amount of washing up liquid into the sump, and using the supplied brush, gently clean all surfaces in the
sump and gently clean the transducer including the metal discs located in the top grooved surface. (Fig.14)
10. When cleaned, thoroughly rinse the sump with clean water to remove all traces of washing up liquid.
11. Clean the Nozzle with the brush and fl ush out thoroughly with water. (Fig.15)
12. Reverse the above steps to reassemble.
button on the remote control. The appliance will switch
5