cecotec BOLERO COOLMARKET COMBI 250 WHITE E Manual De Instrucciones página 33

ENGLISH
3. INSTALLATION
Place of installation
Ventilation condition
- The location you choose for the installation of the refrigerator must be properly ventilated
and away from heat sources. Do not place the refrigerator near heat sources, like a
cooker or pot, and avoid direct sunlight to ensure the cooling effect and save on energy
consumption. Do not place the refrigerator in a damp place, to avoid rust or loss of power.
The result of dividing the total space of the room in which the refrigerator is installed by
the amount of refrigerant load in the refrigerator must not be less than 8 g/m³.
- Note: The amount of refrigerant used by the refrigerator is specified on the rating plate.
Heat dissipation space
During operation, the refrigerator releases heat into the environment. Therefore, you should
leave at least 30 mm of free space at the top, more than 100 mm on both sides, and more than
50 mm at the rear of the refrigerator. Fig. 2
Width Depth (mm) Height A (mm)
(mm) (mm)
540 576 1800 845
Note:
figure 2 only illustrates the space required for the product.
Stable surface
Place the refrigerator on a solid, flat surface (the floor) to keep it stable, otherwise vibrations
and noises will occur. When the refrigerator is placed on a carpet, straw mat, polyvinyl chloride,
solid support plates should be placed under the refrigerator to avoid colour change due to heat
dissipation.
Preparing for use
Waiting time
Once the refrigerator is properly installed and cleaned, do not switch it on immediately. Be
sure to wait at least one hour before switching the refrigerator on to ensure normal operation.
Cleaning
Check the placement of the interior accessory parts and clean the inside with a soft cloth.
B O LE R O COOLM ARKET COM BI 2 50 W HITE E
64
B O LE R O COOLM ARKET COM BI 2 50 INOX E
B (mm) C(°) E (mm) F (mm)
1095 125+/- 5 50 100
On
Connect the plug into a power socket to switch on the compressor. After one hour, open the
freezer door: if the temperature inside the freezer compartment has clearly dropped, the
cooling system is operating normally.
Food storage
After the refrigerator has been in operation for some time, the user may adjust its internal
temperature. Once the refrigerator has reached a suitable interior temperature, put in the food.
These will take 2 to 3 hours to cool down completely. In summer, when the temperature is high,
it may take more than 4 hours for food to cool down completely (try to open the refrigerator
door as rarely as possible).
If the refrigerator is installed in a wet place, be sure to check if the earthed cord and the
leakage breaker are working normally. If vibration noises occur due to contact of the
refrigerator with the wall or if the wall turns black due to air convection around the
compressor, remove the refrigerator from the wall. The installation of the refrigerator may
cause noise interference or image problems in mobile phones, landline phones, radio receivers,
or televisions near the device, so in this case, keep the refrigerator as far away from these
objects as possible.
Changing the opening direction of the door
If desired, you can change the direction in which the door opens, from the right side (by default)
to the left side.
Warning
- The refrigerator must not be connected to the power socket when you change the opening
direction of the door. Make sure to disconnect the plug from the power socket.
- Check figure 5 to check the tools you need.
- It is advisable to change the opening direction of the door between two people.
Fig. 5
A. Tools not supplied
8-mm tube wrench
1.
2. Flat-head screwdriver
3. Spatula
4. Crosshead screwdriver
Wrench
5.
6. 8-mm wrench
B. Additional parts (included in the plastic bag)
Upper-left hinge
7.
8. Upper-left hinge cover
BOLERO COOLMARKET COMBI 250 W HITE E
BOLERO CO OLMARKET CO MBI 250 IN OX E
ENGLISH
65