Idiomas disponibles
Idiomas disponibles
Service, maintenance and repairs
- Obey the maintenance intervals given in this manual.
Overdue maintenance can lead to high costs for repair and
revisions and can render the guarantee null and void.
- Always use Personal Protective Equipment (PPE) to avoid
injury. This also applies for persons who enter the work area.
- Make sure the room is sufficiently ventilated.
- Use tools, materials, lubricants and service techniques which
have been approved by the manufacturer. Never use worn
tools and do not leave any tools in or on the product.
- Use sufficient climbing gear and safety guards when working
on a higher level than 2 metres (local restrictions may
apply).
- Clean the area afterwards.
ATTENTION
Service, maintenance and repairs must be
performed in accordance with directive TRGS 560
and TRGS 528 by authorised, qualified and trained
persons (skilled) using appropriate work practices.
ATTENTION
Before you carry out service, maintenance and/or
repair jobs:
- fully disconnect the unit from the mains
Personal protective equipment (PPE)
Wear respiratory protection and protective
gloves during service, maintenance and
repairs.
WARNING
The industrial vacuum cleaner that you use during
service and maintenance must meet dust class H
according to EN 60335-2-69 or HEPA class
(efficiency ≥99.97% at 0.3 µm).
4
INSTALLATION
4.1
Tools and requirements
You need the following tools and requirements to
install the unit:
- basic tools
- fork-lift truck
- electrical tools
4.1.1
To be sourced locally
General
- Wall mounting hardware for the filter unit
- Mains cable: 4G1.5
- type H05VV-F (PVC, standard cable); or:
- type H05RN-F (rubber, for heavy duty, e.g. when part of
the cable is on the floor)
- Motor cable: 4G1.5
- type H05VV-F (PVC, standard cable); or:
- type H05RN-F (rubber, for heavy duty, e.g. when part of
the cable is on the floor)
- Quick release coupling with a male G 3/8" thread
- Compressed air hose
Wallflex type "SC" only
- Wall mounting hardware for the arm bracket(s)
- Ducting Ø 160 mm between the filter unit and the arm
bracket(s)
8.
The type of hardware depends on the wall type
9.
For mounting at an external position; the type of hardware depends on the
wall type
86958015
8
9
Option
In case of a dustbin extension set:
- duct Ø 200 mm
4.2
Unpacking
Make sure that the product is complete. Refer to
Table I on page 93 for the scope of supply per
configuration.
For an overview of the mounting material per
specific configuration, refer to Fig. IV on page 96.
Extraction arm (1 or 2)
Refer to the installation manual of the PolyArticule, that is
supplied with the product.
4.3
Stationary filter unit
ATTENTION
It is important to follow the mounting sequence as
written in this (4.3) and the next (4.4) paragraph.
The table below explains the different configuration types.
Wallflex type
1200
2400
CSC
SC
A number of installation steps are only applicable to one or
more specific configurations. These are indicated at the
beginning of a certain paragraph. The grey/empty cells are
universal.
Some examples:
Applies to:
CSC
Applies to:
Wallflex 1200
SC
Write your configuration type below.
Wallflex type:
TIP
For stable assembly conditions, we recommend to
leave the filter unit on the pallet (until step 4.6).
4.3.1
Reinforcement plate
Applies to:
CSC
In case of a Wallflex 1200-CSC (direct mount) you must install
a reinforcement plate behind the lower part of the side panel
to support the weight of the arm bracket + extraction arm.
The package of the Wallflex 2400-CSC contains two
reinforcement plates for both sides of the filter housing.
Explanation
1 extraction arm
2 extraction arms
Direct mount
External mount
Applies to all "CSC" types
Applies to all Wallflex 1200 types and
all "SC" types
EN | 5
