Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

MITSUBISHI Room Air Conditioner Optional Grille
Model MLP-448WU
INSTALLATION MANUAL
Correct installation is essential for good performance of the product and safety. Be sure to read this manual
before installation.
THE FOLLOWING SHOULD ALWAYS BE OBSERVED FOR SAFETY
• Be sure to read "THE FOLLOWING SHOULD ALWAYS BE OBSERVED FOR SAFETY" before installation.
• Be sure to observe the warnings and cautions specified here as they include important items related to safety.
• After reading this manual, be sure to keep it together with the OPERATING INSTRUCTIONS for future reference.
Do not perform installation by yourself (user).
Incomplete installation could cause fire or electric shock, injury due to
the unit falling, or leakage of water. Consult the dealer from whom you
purchased the unit or a qualified installer.
Perform the installation securely referring to the installation
manual.
Incomplete installation could cause fire or electric shock, injury due to the
unit falling, or leakage of water.
1. Components
● This kit contains the following parts.
Q'ty
Remark
2. Checks before installation
● Before installing the grille (1), make sure the indoor unit is square with the ceiling opening (or parallel to the wall-ceiling joint).
● Check that the 4 points for securing the grille (1) on the indoor unit are level with the ceiling surface.
Use the installation template supplied with the indoor unit to arrange the position of the indoor unit so that the 4 points for securing the grille (1) are
level with the ceiling surface with a tolerance of 3 mm (1/8 inch). (Fig. 1)
Note: Instructions for using the installation template are provided on the installation template itself.
Note: If the misalignment between the 4 points for securing the grille (1) and the ceiling surface is more than 3 mm (1/8 inch), the intake
grille may not open or close properly.
● Make sure the following is completed: insulation for the refrigerant pipes, drainage pipes, etc. and wiring connections and arrangements.
● Check that any material like ceiling insulation does not protrude to the ceiling opening.
Points for securing grille (1)
Points for securing grille (1)
(1) Grille
1
WARNING
(Could lead to death, serious injury, etc.)
Install the unit securely in a place which can bear the weight of the
unit.
If the installation location cannot bear the weight of the unit, the unit could
fall causing injury.
Be sure to use the parts provided or specified parts for the installa-
tion work.
The use of defective parts could cause fire or electric shock, injury due to
the unit falling, or leakage of water.
Use appropriate protective equipment and tools for safety.
Failure to do so could cause injury.
(2) Screw
6
M5 × 16
Ceiling surface
Point for securing grille (1)
Fig. 1
(3) Screw
1
4 × 12
Drain pan
Make sure these surfaces are flush
with each other (0 - 3 mm [0 -1/8 inch]).
En-1
Tabla de contenido
loading

Resumen de contenidos para Mitsubishi Electric MLP-448WU

  • Página 4: Rejilla Opcional Para Aire Acondicionado De Sala Mitsubishi

    Rejilla opcional para aire acondicionado de sala MITSUBISHI Modelo MLP-448WU MANUAL DE INSTALACIÓN Una instalación correcta es esencial para el buen funcionamiento del producto y su seguridad. Asegúrese de leer este manual antes de la instalación. POR RAZONES DE SEGURIDAD, DEBERÁ OBSERVARSE SIEMPRE LO SIGUIENTE •...
  • Página 5: Instalación De La Rejilla

    3. Instalación de la rejilla 1. Abra la rejilla de entrada presionando las 2 lengüetas de dicha rejilla en la dirección indicada por las flechas. (Fig. 2) Deslice los 2 ejes hacia el interior y retire la rejilla de entrada de los ejes. (Fig. 3) Retire los cordones de seguridad de la rejilla de entrada y retírela.
  • Página 6: Comprobaciones Después De La Instalación

    3. Instalación de la rejilla 10. Enganche los cordones de seguridad de las cubiertas laterales I/D a la rejilla e instálelas. (Fig. 8) • Compruebe que los cierres de las cubiertas laterales I/D estén enganchados de forma segura. (Fig. 8) Colocar en el gancho de la •...
  • Página 12 HEAD OFFICE: TOKYO BUILDING, 2-7-3, MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN DT79B450H01...

Tabla de contenido