EINHELL TE-AG 18/115 Li Manual De Instrucciones página 14

so that the material being ground is directed
away from your body.
•
The position of the guard (4) can be adjusted
to any specific working conditions. Undo the
clamp lever (9) and turn the cover (4) into the
required position.
•
Ensure that the guard (4) correctly covers the
gear wheel casing.
•
Secure the clamp handle (9) again.
•
Ensure that the guard (4) is secure.
Make sure that the guard is perfectly
secure.
Never use the angle grinder without the
guard.
5.3 Trial run for new grinding wheels
Have the angle grinder run in idle mode for at
least 1 minute with the grinding or cutting wheel
fi tted. Replace vibrating wheels immediately.
6. Operation
6.1 Charging the Lithium-Ion battery
(not included)
The corresponding instructions can be found
in the original operating instructions for your
charger.
6.2 Switch (Fig. 4)
The angle grinder comes with a safety switch
which is designed to prevent accidents. To switch
on, push the On/Off switch (2) to the right and
then forwards. To switch off the angle grinder,
depress the On/Off switch (2) at the back. The
On/Off switch (2) will jump back into its starting
position.
Wait until the machine has reached its
top speed. You can then position the angle
grinder on the workpiece and machine it.
6.3 Battery capacity indicator
(Fig. 13 / item 10)
Press the battery capacity indicator switch (11).
The battery capacity indicator (10) shows the
charge status of the battery using 3 LEDs.
All 3 LEDs lit:
The battery is fully charged.
2 or 1 LED(s) lit:
The battery has an adequate remaining charge.
Anl_TE_AG_18_115_Li_SPK7_USA.indb 14 Anl_TE_AG_18_115_Li_SPK7_USA.indb 14
EN
1 LED fl ashing:
The battery is empty, recharge the battery.
All LEDs fl ashing:
The temperature of the battery is too low. Remove
the battery from the device and leave it at room
temperature for a day. If the error occurs again,
this means that the battery has been completely
depth-discharged and is defective. Remove the
battery from the device. Never use or charge a
defective battery.
6.4 Changing the grinding wheels (Fig. 5 / 6)
Use the face spanner (5) supplied to change the
grinding wheels. The face spanner (5) is stored in
the additional handle (3). Pull the face spanner (5)
out of the additional handle (3) when you need it.
Danger! For safety reasons, the angle grinder
must not be operated with the face spanner (5)
inserted in it.
Warning!
•
Changing the wheel is easy thanks to the
spindle lock.
•
Press the spindle lock and allow the grinding
wheel to engage.
•
Use the face spanner to undo the flange nut.
(see Fig. 6)
•
Change the grinding or cutting wheel and
tighten the flange nut with the face spanner.
Important!
Only ever press the spindle lock when the
motor and grinding wheel are at a standstill!
The spindle lock must be kept pressed while
the wheel is being changed!
For grinding or cutting wheels with a thickness
of up to approx. ⅛" (3 mm), screw the fl ange nut
on with the fl at side facing the grinding or cutting
wheel.
6.5 Position of the fl anges when using
grinding wheels and cutting wheels
(Fig. 7-10)
•
Position of the flange when using an offset or
a straight grinding wheel (Fig. 8)
a) Clamping flange (6)
b) Flange nut (7)
•
Position of the flange when using an offset
cutting wheel (Fig. 9)
a) Clamping flange (6)
b) Flange nut (7)
•
Position of the flange when using a straight
cutting wheel (Fig. 10)
a) Clamping flange (6)
- 14 -
02.05.2022 15:26:14 02.05.2022 15:26:14