DeWalt DCS578 Manual De Instrucciones página 36

ENglIsH
Proper Hand Position (Fig. G)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the main
handle 18 and one hand on the auxilliary handle
Worklight (Fig. A)

CAUTION: Do not stare into worklight. Serious eye
injury could result.
The worklight 11 is activated when the trigger switch is
depressed, and will automatically turn off 20 seconds after
the trigger switch is released. If the trigger switch remains
depressed, the worklight will remain on.
NoTE: The worklight is for lighting the immediate work
surface and is not intended to be used as a flashlight.
Trigger Switch (Fig. F)

WARNING: This tool has no provision to lock the
trigger switch in the ON position and should never be
locked ON by any other means.
Release the trigger switch lock-off button
button as shown. Pull the trigger switch
on. Releasing the trigger switch turns the motor off.
Changing Blades (Fig. G, H, I)

WARNING: Remove battery from tool before
changing blades.
To install the Blade (Fig. G, H, I)
1. Retract the lower blade guard
retracting lever 6 and place the blade on the saw
spindle against the inner clamp washer, making sure
that the blade will rotate in the proper direction (the
direction of the rotation arrow on the saw blade and the
teeth must point in the same direction as the direction of
rotation arrow on the lower blade guard). Do not assume
that the printing on the blade will always be facing
you when properly installed. When retracting the lower
blade guard to install the blade, check the condition
and operation of the lower blade guard to assure that it
is working properly. Make sure it moves freely and does
not touch the blade or any other part, in all angles and
depths of cut.
2. Place outer clamp washer
large flat surface against the blade with beveled side
facing out.
3. Thread blade clamping screw
hand (screw has right-hand threads and must be turned
clockwise to tighten).
4. Depress the blade lock button
spindle with the blade wrench
engages and the blade stops rotating (Fig. G).
5. Tighten the blade clamping screw firmly with the blade
wrench.
NoTE: Never engage the blade lock while saw is running, or
engage in an effort to stop the tool. Never turn the saw on
while the blade lock is engaged. Serious damage to your saw
34
12 .
1 by pressing the
2 to turn the motor
7 using the lower blade
16 on saw spindle with the
8 into saw spindle by
11 while turning the saw
14 until the blade lock
will result.
To Replace the Blade (Fig. G, H)
1. To loosen the blade clamping screw
blade lock button
11
blade wrench until the blade lock engages and the
14
blade stops rotating. With the blade lock engaged, turn
the blade clamping screw counterclockwise with the
blade wrench (screw has right-hand threads and must be
turned counterclockwise to loosen).
2. Remove the blade clamping screw
washer 16 only. Remove old blade.
3. Clean any sawdust that may have accumulated in the
guard or clamp washer area and check the condition
and operation of the lower blade guard as previously
outlined. Do not lubricate this area.
4. Select the proper blade for the application (see Blades).
Always use blades that are the correct size (diameter)
with the proper size and shape center hole for mounting
on the saw spindle. Always assure that the maximum
recommended speed (rpm) on the saw blade meets or
exceeds the speed (rpm) of the saw.
5. Follow steps 2 through 5 under To Install the Blade,
making sure that the blade will rotate in the proper
direction.
Lower Blade Guard

WARNING: The lower blade guard is a safety
feature which reduces the risk of serious personal
injury. Never use the saw if the lower blade
guard is missing, damaged, misassembled
or not working properly. Do not rely on the
lower blade guard to protect you under all
circumstances. Your safety depends on following
all warnings and precautions as well as proper
operation of the saw. Check lower blade guard
for proper closing before each use as outlined
in Further safety Instructions for all saws.
If the lower blade guard is missing or not
working properly, have the saw serviced before
using. To assure product safety and reliability,
repair, maintenance and adjustment should be
performed by an authorized service center or
other qualified service organization, always using
identical replacement parts.
Blades

WARNING: To minimize the risk of eye injury, always
use eye protection. Carbide is a hard but brittle
material. Foreign objects in the workpiece such as wire
or nails can cause tips to crack or break. Only operate
saw when proper saw blade guard is in place. Mount
blade securely in proper rotation before using, and
always use a clean, sharp blade.

WARNING: Do not cut metal, plastic, concrete,
masonry or fiber cement materials with this saw.
Do not use abrasive wheels or blades. A dull blade will cause
slow inefficient cutting, overload on the saw motor, excessive
splintering, and could increase the possibility of kickback.
, depress the
8
and turn the saw spindle with the
8 and outer clamp