Before Use; Unpacking; Assembly And Preparation; Selecting And Putting On The Nozzle - Dirt Devil EQU Silence M7120 Manual De Instrucciones

3 Before use

3.1 Unpacking

3 Before use
ATTENTION:
Always transport/send the appliance in its original packaging to avoid
transport damage. Keep the packaging for such an event. However, dis-
pose of no-longer-needed packaging material properly.

3.2 Assembly and preparation

A
2
Datum Erstgebrauch
/ date of first use
3

3.3 Selecting and putting on the nozzle

WARNING:
Danger of injury! Only attach the parts if the appliance is not connected
to the power supply. Otherwise, the appliance could be switched on by
accident.
A
*
3
*
2
4
ATTENTION:
Our turbo brush (Fig. 4/A3*) serves solely to vacuum non-sensitive car-
pets, runners, doormats, and the like. Do not clean any objects with the
turbo brush that you would not clean without a second thought with a
conventional brush. Therefore, do not clean furniture, or materials with a
delicate texture, nor any other high-quality or polished substrates with
the turbo brush. Otherwise material damage might occur. If in doubt,
refrain from using the turbo brush.
16
B
A
B
3
4
1
1. Unpack the appliance and all its accessories.
2. Check that the contents are intact (Fig. 1).
NOTE:
Immediately contact your dealer if you have found damage resulting
from transport.
WARNING:
Danger of injury! Only attach the parts if the appliance is not connected
to the power supply. Otherwise, the appliance could be switched on by
accident.
1. Insert the suction hose adapter into the intake opening of the appliance
(Fig. 2/A) as shown:
- When doing so, ensure that the projections on the adapter engage
90°
with the recesses of the intake opening (Fig. 2/A, arrow).
90°
- Then rotate the adapter clockwise through about 90° (Fig. 2/B) until
it is secure in the intake opening.
2. If you want to use the telescopic tube (Fig. 1/24), insert the handle
(Fig. 1/14) into the upper end of the telescopic tube.
3. If you have attached the telescopic tube, adjust its length:
- Press down the release latch on the tube to (Fig. 1/25) do this. Then
extend the telescopic tube to the desired length.
- Let go of the release catch while pulling until it locks in place. You will
B
hear a distinct click.
4. Enter the date onto the hygienic exhaust filter:
- Slide the catch of the exhaust filter cover to the side (Fig. 3/A) and re-
move the exhaust filter cover.
- Remove the hygienic exhaust filter using the tongue (Fig. 3/B) provid-
ed for this purpose and enter the current date.
- Put the exhaust filter back into its holder (Fig. 3/B).
- Put the exhaust filter cover back on. See
hygienic exhaust filter" for further information.
ATTENTION:
Before vacuuming, make sure that the fitted nozzle suits the surface to
be cleaned. Also observe the flooring manufacturer's recommendations.
1. Select the nozzle with which you want to vacuum.
- As well as the floor nozzle (Fig. 4/A1), the crevice nozzle (Fig. 4/B1)
and the 2-in-1 combi nozzle (Fig. 4/B2) are included as accessories
2
in the scope of delivery.
Crevice nozzle (Fig. 4/B1):
For removing dust from hard to reach places.
2-in-1 combi-nozzle (Fig. 4/B2)
to be used as:
Furniture brush (Fig. 4/B2):
To remove dust from furniture and objects with delicate surfaces.
Upholstery nozzle (Fig. 4/B3):
To remove dust from soft, scratch-resistant surfaces (e.g. uphol-
stered furniture). To do so, simply pull the brush attachment (Fig. 4/
B4) off the furniture brush.
- *Optionally available (* i.e. included in the scope of delivery de-
1
pending on model and features) are also:
Parquet brush (Fig. 4/A2*):
For vacuuming delicate floors (e.g. parquet, laminate).
Turbo brush (Fig. 4/A3*):
Is used to vacuum non-sensitive carpets, runners, mats, and the like.
2. Attach the selected nozzle to the bottom end of the telescopic tube
(Fig. 4/A) or of the handle (Fig. 4/B).
Chapter 5.3, "Cleaning the