Idiomas disponibles
Idiomas disponibles
FL420 Electronic Locking User Guide — General Operating Instructions
Edit Existing CS Code:
Note: Cannot change User Code itself but can Edit information tied to
User Code (e.g., PIN).
- Press OK key to wake up touch pad.
- Enter User Code and press OK.
- Press ''FUNCTION'' key several times until ''CHANGE CS PIN?'' is
displayed.
- Enter current PIN or Press OK if there is no current PIN.
- Enter New PIN or Press OK to skip.
- Press OK to accept new PIN or ''CLEAR'' to change.
- Press ''SIGN OUT'' to exit & lock cart.
Add or Change Card ID:
Note: Only for carts that is equipped with a card reader. This function
can be performed by the Supervisor or User. The cart main lock must be
disengaged.
- Press OK key to wake up touch pad.
- Enter User Code and press OK.
- Press ''FUNCTION'' key several times until ''SET OR CHANGE YOUR
CARD ID'' is displayed & Press OK.
- Follow prompts. If using a magnetic card or bar code reader, slide the
card through the reader from back to front. If using a proximity card,
pass it over the reader.
- If the card is not properly read an Error Reading Card message will
display. Try swiping the card again (try not to angle the card as it
passes through or in front of the reader).
- When the card is read the message ''NEW CARD ID IS 12345678''.
Press OK to accept or clear to change.
- Press ''SIGN OUT'' to exit User Mode.
Section 8: CS Code Functions
Edit Existing CS Code:
Note: Cannot change CS Code itself but can Edit information tied to CS
Code (e.g., PIN).
- Press OK key to wake up touch pad.
- Enter User Code and press OK.
- Press ''FUNCTION'' key several times until ''CHANGE CS PIN?'' is
displayed.
- Enter current PIN or Press OK if there is no current PIN.
- Enter New PIN or Press OK to skip.
- Press OK to accept new PIN.
- Press ''SIGN OUT'' to exit & lock cart.
Section 9: Service Code Functions
Adjust the Display Contrast:
- Press OK to wake up touch pad.
- Enter Service Code and press OK.
- Press ''FUNCTION'' key several times until ''ADJUST THE DISPLAY
CONTRAST'' is displayed & Press OK.
- Press and hold down the side arrow keys < to decrease or > to increase
the contrast.
- Press OK.
- Press ''SIGN OUT'' to exit Service Mode.
Unlock the Cart:
Note: If the cart fails to unlock or relock in this test, it may be because
the cart's Servomotor is not properly calibrated (see section below) lock
failures may also be due to jammed drawers or an improperly adjusted
cart lock switch.
- Lock the cart manually before starting this test.
- Press OK to wake up touch pad.
- Enter Service Code and press OK.
- Press ''FUNCTION'' key several times until ''UNLOCK CART'' is
displayed & Press OK, the cart will unlock.
- Press OK to relock the cart.
- If the cart fails to unlock or relock, an appropriate message will be
displayed.
- Press ''SIGN OUT'' to exit Service Mode.
Test Keyless CS (Narcotic) Drawers:
Note: Only for carts that are equipped with a Controlled Substance
drawer. For security reasons, narcotics drawers can only be opened by an
authorized person with a valid CS ID Code.
Check the Keyless CS Drawer's Servomotor:
- Unlock the cart's main lock (see Section 2).
- Press the CS key and enter a valid CS ID code to unlock the CS drawer
with a key.
- The display reads ''NARC DRAWER UNLOCKED''.
- Pull the drawer open. The Servomotor should rotate a small cam
approximately 1/4 turn to push the drawer latch past its stop. If it does
not open, the CS drawer may not be confi gured (see section below), or
the servo or cable may be at fault, contact the Metro Customer Service.
Test the Keyless CS Drawer Switches:
- If the drawer does not open, unlock it with a metal key to test the drawer
switch.
- Open and close the drawer, the display should change from ''NARC
DRAWER OPEN'' to ''NARC DRAWER UNLOCKED''.
- The NARC drawer switch test can also be performed by pulling the
drawer forward while it is locked. The display should change as
described above.
- If the drawer fails the switch test, close and lock the drawer. Sign out
then sign in again using the Service ID number.
- Press ''FUNCTION'' key several times until ''TEST KEYPAD AND
SWITCHES'' is displayed.
- Try the switch test again. If the drawer location number displays on the
right upper part of the display, the switch is functioning.
- If it does not, the drawer may not be confi gured (see section below or
contact Metro Customer Service).
- Press ''SIGN OUT'' to exit Service Mode.
Keypad Test:
- Press OK to wake up touch pad.
- Enter Service Code and press OK.
- Press ''FUNCTION'' key several times until ''TEST THE KEYPAD AND
SWITCHES'' is displayed & press OK.
- PRESS VARIOUS KEYS AND CHARACTERS WILL DISPLAY AS SHOWN
BELOW ON CHART.
- Press OK once and an ''O'' will appear in the upper part of the screen,
Press OK again to exit the test.
- Press ''SIGN OUT'' to exit Service Mode.
Test keypad keys:
- Press various keys and a charactesr will display as follows:
Key Selected
Displays (left upper line of display)
0 to 9
Sign Out
OK
Function
Clear
CS
Select
<
>
Display Light
Key Lock Switch Test:
Unlock the cart with a key. An ''L'' should display in the upper right section
of the display.
- Press OK twice to end test.
- Press ''SIGN OUT'' to exit Service Mode.
0 to 9
S
O
F
C
N
T
<
>
D
Continued...
