Idiomas disponibles
Idiomas disponibles
DANGER! Observe the tightening torques specified on the handlebar stem. Incorrectly tightened torques can lead to malfunctioning or
failure of the component resulting in loss of vehicle control and crashes!
Never use the product if assembly work is incomplete or incorrectly carried out. Doing so endangers yourself and other traffic.
WARNING! Turn the handlebar to the left and right, do not use the bike if you notice abnormal steering behaviour (play in the steering or
uneven resistance) or if cracks and crazing are evident.
In the event of an accidental fall or accident, the handlebar will almost certainly be involved. It will be subjected to heavy stress and impacts.
The presence of deep scratches and cracks indicates that parts must be replaced.
WARNING! If the handlebar is damaged, use of the Bianchi Oltre Pro and Oltre Rc bicycle must be stopped immediately. Only return to
use your Bianchi Oltre Pro and Oltre RC after your specialist dealer has thoroughly inspected it and, if necessary, replaced the handlebar
if damaged.
The Oltre Pro and Oltre RC handlebars are supplied with the cycle computer
mount, cycle computer insert/hook and adapter/base for Garmin and Wa-
hoo. Follow the instruction diagram and pictures below.
1) Insert the holder in the front and centre of the handlebar
2) Insert the connecting and locking insert in the rear and centre of the
handlebar
3) Apply a drop of medium strength glue such as Loctite 242 to the cycle
computer support locking screws. Tighten the two M3x18 mm screws with
an insert torque wrench (2.5 mm hexagonal) 1 Nm maximum torque.
Your Garmin or Wahoo cycle computer comes with a safety strap / elastic
band which we advise you to use. We invite you to read the manufacturer's
manual carefully and to comply fully it in order to not damaging your cycle
computer.
OLTRE HANDLEBAR STEM AND BEND
The handlebar kit that comes with the Bianchi Oltre frame consists of a stem and handlebar bend specially designed for this frame, the components
are Velomann branded.
It should be noted that failure to comply with the warnings and prescriptions contained in this package insert exempts the manufacturer from any
liability. When assembled, the cables will enter the handlebar bend near the levers and exit under the handlebar stem and enter the frame through the
shims and headset.
The height adjustment of this type of handlebar stem can originally be carried out by your specialist dealer. In view of the importance and complexity
of this specific component, we always advise you to consult your specialist retailer for stem adjustment and to fully understand the mechanisms and
methods of adjustment.
DANGER! Observe the tightening torques specified on the stem. Incorrectly tightened torques can lead to malfunctioning or breakage of
the component resulting in loss of vehicle control and crashes!
Never use the product if assembly work is incomplete or incorrectly carried out. Doing so endangers yourself and other traffic.
WARNING! Turn the handlebar to the left and right, do not use the bike if you notice abnormal steering behaviour (play in the steering or
uneven resistance) or if cracks and crazing are evident.
In the event of a fall or accident, the handlebar will almost certainly be involved. It will be subjected to heavy stress and impacts. The presence of deep
scratches and cracks indicates that parts must be replaced.
WARNING! If the handlebar is damaged, use of the Bianchi Oltre bicycle must be discontinued immediately.
Only return to use the Bianchi Oltre after the specialist dealer has thoroughly inspected it and, if necessary, replaced the handlebar if
damaged.
THREADLOCKER
THREADLOCKER
OLTRE, OLTRE PRO, OLTRE RC THRU-AXLE PASSING PINS
WARNING! Please be very careful and observe the following warnings.
Failure to comply with the following warnings and the prescriptions contained in this package insert exempts the manufacturer from any liability.
The supplied thru-axle pins, as opposed to 'quick release' locks, are screwed directly onto the frame and fork dropouts, via an M12 thread.
Observe the tightening torques indicated on the pins.
In the Oltre, Oltre Pro and Oltre RC frames, the female threads housed in the frame and fork are of the blind type: it follows that the thru-axle pin
with male thread has a specific length in order to be able to assemble the wheels safely.
The use of a different axle from the one supplied may result in incorrect assembly of the wheel and compromise the integrity of the frame and fork.
WARNING! Observe and use the through-bolt pins supplied with the product. The use of through-bolt pins other than those specified may
cause the frame and/or fork to break.
DANGER! Incorrectly fitted wheels can cause falls and serious accidents. If in doubt, contact your specialist dealer.
DANGER! Observe the tightening torque specified on the through-bolts pins. Never exceed the maximum tightening torque specified.
Incorrect tightening may damage the frame and fork.
OLTRE, OLTRE PRO, OLTRE RC SEAT POST/EXPANDER LOCKING BLOCK
The supplied locking block/expander is a specific component for the three frames: Oltre, Oltre Pro and Oltre RC. Without it it is not possible to lock the
seat post in the desired position.
Follow the warnings below carefully. Failure to observe the warnings and prescriptions contained in this package insert exempts the manufacturer from
any liability. It should also be noted that any damage and/or breakage resulting from operation not compling with the warnings and/or instructions
detailed herein, are not covered by the warranty since the damage and/or breakage does not depend on non-compliance of the product.
To set the saddle height, loosen the M5 seatpost clamping screw. Find access to the screw through the slot located on the underside of the top tube in
the area where it intersects with the seat tube (see image 5a and 5b).
IMAGE 5A
IMAGE 5B
post only downwards (by a few millimeters) to check the separation between the two components.
Be extremely careful when using the service stand with seat post attachment! Fixing the product via seat post may cause forces on the frame,
avoid applying excessive upward forces or pushing the frame down!
The recommended locking torque of the locking block/expander is 6Nm. To avoid damaging the frame, it is recommended to use a 4 mm hexagonal
insert 100 mm long (see image 6a) and to use a torque spanner to tighten the latch/expander block screw (see image 6b).
WARNING! Do not remove, move or adjust the seat
post (e.g. to adjust the saddle height) without loosen-
ing the clamping bolt of the expander!
Never pull the seat post upwards if the seat post ex-
pander is not completely loosened, this action can
cause the frame to break!
The expander creates friction between its surface and
the seat post one. Carry out a sliding test of the seat
