Tabla de contenido
Idiomas disponibles
Idiomas disponibles
2. To store the telescoping handle
release button
17
and slide the telescoping handle
down and into the pressure washer body. You will hear an
auidible click when it snaps into position.
3. To move the pressure washer
transport wheels
21
unit by the telescoping handle.
Attaching Spray Handle (Fig. F)
1. To connect the spray handle
insert the end of the spray handle onto the end of the
spray wand.
2. Press in and turn the spray handle counterclockwise to
lock it into position.
Attaching High Pressure Hose (Fig. A, G)
CAUTION: NEVER PULL WATER SUPPLY HOSE TO
MOVE pressure washer. This could damage hose and/
or pump inlet.
This pressure washer has a hook and loop hose storage
strap
27
on the cage
15
store the coiled high pressure hose
nOTE: Uncoil the high pressure hose
prevent kinks.
nOTE: Avoid cross threading when installing the hose. Cross
threading will cause leaks.
1. To connect the high pressure hose
handle
7
, thread the hose collar
coupler
29
.
2. To connect the high pressure hose to the pressure
washer unit
11
, thread the hose collar
pressure water outlet
Attaching Garden Hose (Fig. H)
nOTE: Before connecting the garden hose to the pressure
washer unit, run water through the garden hose for thirty
seconds to clear any debris from inside the garden hose.
1. To connect a garden hose to the
pressure washer unit
garden hose
30
inside the water intake
2. Securely tighten the garden hose by hand.
nOTE: Always disconnect the garden hose after usage.
Attaching Nozzles (Fig. I)
DANGER: Risk of fluid injection. Do not direct
discharge stream toward persons, unprotected skin,
eyes or any pets or animals. Serious injury will occur.
WARNING: Flying objects could cause risk of serious
injury. DO NOT attempt to change nozzles while
pressure washer is running. Turn pressure washer unit
OFF before changing nozzles.
1. To connect a nozzle to the spray wand
connect collar
6
toward the spray wand and insert the
appropriate nozzle.
2. Release the quick connect collar to lock the nozzle in place.
3. Give the nozzle a firm tug after the quick connect collar
has locked into place to ensure the nozzle is locked
into place.
16
, press the handle
11
, tilt the unit so the
are touching the ground and pull the
7
to the spray wand
of the pressure washer unit to
1
.
1
before installation to
1
to the spray
28
onto the inlet
28
onto the high
19
.
11
, place the end of the
18
5
, pull the quick
nOTE: The nozzles listed below might not be included with your
pressure washer but are available for purchase at an additional cost.
Common Spray Nozzles
15 ° Orange Nozzle
25 ° Green Nozzle
40 ° White Nozzle
Black Turbo Nozzle
5
,
To Attach the Suction Hose (Fig. J)
Use the suction hose to pull water from a bucket or other
fresh water source.
NOTICE: Do not use to suction soap, chemicals, dirty
or corrosive liquids, such as window cleaner, plant food,
fertilizers or bleach. Do not use with salt water.
nOTE: Avoid cross threading when installing the hose. Cross
threading will cause leaks.
1. To connect the suction hose
pressure washer unit
collar
2. Securely tighten the suction hose collar
nOTE: Always disconnect the suction hose after usage.
3. Place other end of suction hose, with the filter
into a container of fresh water or a fresh water source.
4. Adjust the float ball
stays covered in the liquid.
5. Select the correct nozzle to be used. See Attaching
Nozzles chart
6. After the job being performed is complete, place the
suction hose into a container of clean water and draw the
clean water through the system to rinse.
Removing Soap Bottle from Storage (Fig. K)
Always completely empty the soap bottle
1. Unlock the telescoping handle
upwards so you can access the soap bottle
2. To remove the soap bottle
.
space in the pressure washer unit, grasp the soap
bottle
the pressure washer unit.
3. To place the soap bottle
the soap bottle
snaps into the built in storage space in the pressure
washer unit.
4. Ensure that soap bottle
position by gently tugging on the soap bottle
Common Applications
For brick or masonry.
For vinyl siding.
For automotive washing.
For abrasive cleaning.
2
11
, thread the suction hose
31
onto the water intake
3
on the suction hose so the filter
16
26
26
with one hand and pull it out and away from
26
into its storage slot, press
26
firmly into the storage slot until it
26
is secured into the storage
English
to the
18
.
31
by hand.
4
on it,
4
26
before storing.
, and slide the handle
26
.
from the built in storage
26
.
11
Tabla de contenido
