Changing Tools - stayer SCR 216 W Manual De Instrucciones

This machine does not have any kind of protection against
the entry of water so that its use in exterior or interior
environmental conditions with a risk of precipitations is
forbidden.
SETTINGS AND TESTING
7.
Warning!
Before any intervention on the electrical tool remove jack
from power socket.
If the machine has been subject to prolonged or intense
use, it must be checked and adjusted so as to ensure the
machine's correct quality of service and safety.
This requires knowledge, experience and special tools.
The official technical service of Stayer Iberica S.A.
will carry out that work for you in a quick thorough and
inexpensive manner.
Locking in the down position
1 Start with the head raised.
2
Unlock the head by pressing the plate (3) (only on
SCR255W)
3
Lower the head to the lowest position.
4 Twist and push the pin (4) all in the way to lock the
head. When fitted correctly, the head will not be able
to lift upwards.
Adjusting the angle for vertical cut at 45° (bevel)
Verification
1
Release the vertical adjustment of the head by
loosening the head angle control lever (5). Remove
the extendible lateral support guide by loosening the
knob (17) before you can tilt the machine head.
2
Tilt the head as far right as possible (45°). On the
SCR315W model, the head can tilt to both sides. To
tilt the head all the way to the left, pull the pin (18).
3 Check the angle using a duly calibrated angle chart
or goniometer (minimum accuracy +/- 5°), placing one
side on the cutting table and the other side on the
cutting blade.
4 If the face of the angle chart does not fit the blade
exactly or if there is a deviation greater than +/- 20°
when using the goniometer, an adjustment must be
made.
Adjustment
1
Using a goniometer (minimum accuracy +/- 5°), place
one side on the cutting table and the other side on the
cutting blade.
2 Adjust the screws located on the head tilt axis (B) until
you reach a measurement of 90° / 45°.

CHANGING TOOLS

8.
Attention!
This operation must be carried out with the machine
unplugged and with the disk still. Use protective gloves.
- Use obligatorily disk according to normative EN 847-1
- Use obligatorily the regulatory push stick and save it
away if not use it.
- Use of fast steel disks prohibited (HSS)
- Use of defective or deformed prohibited
- Replace the table insert when worn
ENGLISH
19
Removing the cutting blade
1 Lock the head in the up position.
2
Detach the blade guard by pulling upwards.
3 On the SCR216W and SCR255CW models, you must
remove the blade guard before you can access the
blade. To remove the guard, unscrew the 3 screws
(12). To do so, set the guard in such a way that the
screws become accessible.4.
4
Press the blade locking knob (7) and carefully turn the
blade until it locks.
5 Remove the blade to be replaced by turning the screw
clockwise.
Changing the cutting blade
1 Carefully clean all sawdust and dirt from the brackets,
flanges and inside of the guards.
2 Place the new cutting blade so that the direction of
the arrow on the front of the casing matches the arrow
engraved on the blade and the tilt of the blade's teeth.
3 Attach the flange and its screw
4 Tighten the
SCR216W and SCR255CW models, the blade guard
must be put back in place by replacing the screws (12)
and tightening them completely.
5 Place the blade guard in its original protective position
by pulling downwards. The blade guard should return
to its original position automatically when released.
6
Check the correct operation by simulating a cutting
operation at idle speed.
FIXING FOR OPERATION
9.
Whenever possible, the workpiece must be fixed in such a
manner that the hand does not intervene.
During the cut, keep the workpiece fixed to the support.
ALL MACHINES ARE PREPARED FOR MOUNTING
CLAMPS ALLOWING FASTENING THE PROFILE IN A
SAFE MANNER.
To avoid deformations of the workpieces during fixing
thereof, the use of wooden profiles being easily applicable
to the movable jaws of the clamps is advised. Clamps can
be easily extracted and leave the working surface totally
clear.
For cutting long workpieces under safe conditions it is
essential to hold them with additional supports.
LIMITS REGARDING THE WORKPIECE SIZE
10.
Limits for all models as included in the present manual on
page 3.
GENERAL INSTRUCTIONS FOR USE
11.
Warning!
1
Do NOT use the machine if it is in a bad condition
or lacks parts including the prescribed upper guards
(the illustrations of the present manual may be used
as an orientative guide). Unplug it, remove it from the
working area and immediately send it to an authorized
technical service.
2
Know and comply with all safety measures before you
start the machine.
- Obligatory used of aspiration particle system when
cutting the wood.
19
screw counter-clockwise. On the