Special Safety Precautions - stayer SCR 216 W Manual De Instrucciones

Carrying out the cutting operation on the lower
table
1 Prepare workpiece by fastening it in a completely safe
manner.
2 Set the length of the cut by loosening the rail knob
(8). If you wish to make a long cut using the full length
of the telescopic rail (9), loosen the locking knob (8)
completely.
3
Start-up the electric machine pressing the switch on
the grip (6). On the SCR216W and SCR315W models,
press the locking button (3) beforehand.
4 Wait for some seconds until the cutting disk reaches
its maximum speed.
5 Slowly lower the head with the help of the grip in a
smooth, continuous movement. On the SCR255CW
model, you must remove the plate (3) before lowering
the head.
6 Exert pressure in the blade's direction of advance
with an intensity being suitable for the material to be
cut. To perform long cuts or cuts using the telescopic rail, start the cut with the head fully extended over the
telescopic rail (9) so that it is in its closest position
closest to you. First, start the cut by lowering the head
to its lowest position, then slowly push the head away
from you so that it slides along the telescopic rail (9)
and performs the long cut.
WARNING:
Never perform a cut from back to front, pulling the head
towards you. This could cause serious accidents and
could also damage the piece you are cutting.
7
Once the cutting operation has been completed, raise
operating head again. Stop the machine by pushing
switch.
Using cutting extenders (10)
The tool includes 2 extenders for cutting long workpieces
(10).
The extenders have 2 screws at the ends of the rods that
act as a stop. To fit the extenders, remove these screws,
insert the rods into the corresponding holes at the base of
the tool and replace the screws under the base.
This will prevent the extenders from coming out of the
machine if tugged on.
The extenders can be used to support large workpieces,
and they must be fixed in place with the knobs located at
the rear of the cutting table (19).
Using the depth stop (11)
The tool includes a depth stop for tasks that require partial
cuts or cuts with reduced visibility.
Use the depth stop screw (11) to adjust the depth of a cut.
The more this screw is screwed in, the less you can lower
the head and the shallower the cuts will be.
Laser guide (14)
DANGER LASER RADIATION
Do not look directly at the beam.
Laser specifications as per EN62841-1:
CLASS 2
Wave length: 650 mm / Power: < 1mW
The purpose of the laser guide is to obtain a precise cut.
ENGLISH
21
Use the laser guide (14) whenever the job requires a
precise cut or when there are guiding lines drawn on the
workpiece surface.
To use the laser guide simply press the switch (16) located
on the handle of the tool.
Once you have finished using it, press the same switch to
turn it off.
PRECAUTIONS AND PROTECTIVE GARMENT
12.
This electrical tool may only be handled by adult personnel
who have received suitable training and instructions,
complying with laws as established to this respect and
what has been set forth as a matter of prevention for the
working place.
In addition, the operator must have understood and
assimilated, and fully comply with the present manual.
This machine requires the use of the following individual
protective equipments:
1
Protective helmet
2 Integral face-protecting equipment (eyes and face)
against impacts
3 Ear protectors
4
Dust mask
5 Protective gloves against mechanical aggression
6
Boots with toe caps and insoles
7 Working garment
8 Tool bag
9 Safety belt (occasional)

SPECIAL SAFETY PRECAUTIONS

13.
Safety Precautions
- Do not use saw blades that are damaged or deformed.
- Do not use the saw without guards in position,
especially after a mode change, and keep guards in
good working properly maintained.
- Replace the block of the table when worn.
- Only use blades recommended by the manufacturer
saw, with a warning that the keel should not be thicker
than the width of the groove of the cut made by the
saw blade and not thinner than the body of the blade;
Specific saw blades for cutting wood must comply with
EN 847-1.
- Do not use saw blades made of high speed steel.
- Connect the saw to a dust collection system when
sawing wood.
- Always store the push stick in place when not in use
Description of risks specifically related to the
machine
Any of the following prior risk conditions must have existed
for the risks to become real:
1
The operator has not been suitably trained.
2 The mitre saw has not been installed suitably.
3
The mitre saw has not been maintained correctly.
4 The mitre saw has been disassembled and then been
assembled incorrectly.
5 The mitre saw has been disassembled and assembled
with parts lacking.
6 Operator does not use the protection as indicated.
7 Operator grasps the workpiece with his/her hand.
21