Changing Tools - stayer SC250W Manual De Instrucciones

3.The distance between the inside of keel 37 and the
outside of the teeth of the disk must be between 3mm
and 5mm at any visible point. If the measurements are
not within the range of the figure, proceed to adjusting.
4. The keel 37 must be perfectly aligned with the disc 21.
If not do not use the machine and take it to service.
Adjusting
1.Remove the locking element 38 of the guard 26 of the
upper table.
2.Tilt guard 26 backwards.
3.Loosen the adjusting screws 46 of the keel.
4.Adjust the height of the keel in such a manner that the
distance between the inside of keel 37 and the outside
of the teeth of the disk must be between 3mm and
5mm at any visible point.
5.Tighten adjustment screws 46 of the keel.
6.Place the guard in its position.

9. Changing tools

Attention!
This operation must be carried out with the machine unplugged
and with the disk still. Use protective gloves.
- Use obligatorily disk according to normative EN 847-1
- Use obligatorily disc thicker than the riving knife
- Use obligatorily the regulatory push stick and save it
away if not use it.
- Use of fast steel discks prohibited (HSS)
- Use of defective or deformed prohibited
- Replace the table insert when worn
Removal of the cutting disk
IMAGES A B K L
1.Place the head in its upper blocking position by tilting
the head upwards until abutting.
2.Immobilize flange 23 by means of the flange wrench as
delivered together with the equipment.
3.Loosen hexagon head screw 22 clockwise with the
tubular key as delivered together with the equipment.
4.Tighten button 30 to unblock the movable guard 5.
5.Clear guard 5 by pulling it upwards.
6.Hold the disc with one hand
7.Remove the flange and the hexagon head screw.
8.Remove the disk to be changed.
Only SC2500W
1.Place the head in its upper blocking position by tilting
the head upwards until abutting.
2.Loosen the 5 screws 54 holding the casing 1.
3.Loosen the 2 screws keel 55 of the top 56 top table
4.Immobilize flange 23 by means of the flange wrench as
delivered together with the equipment.
5.Loosen hexagon head screw 22 clockwise with the
tubular key as delivered together with the equipment.
6.Tighten button 30 to unblock the movable guard 5.
7.Clear guard 5 by pulling it upwards.
8.Hold the disc with one hand
9.Remove the flange and the hexagon head screw.
10.Remove the disk to be changed.
ENGLISH
52
Changing the cutting disk
1.Carefully clean sawdust and debris from the supports,
flanges and the insides of the guards.
2.Place the new cutting disk in such a manner that the
direction of the arrow of the front side of the casing 1
coincides with the arrow engraved in the disk and with
the direction of the disk teeth as such.
3.Place the flange and the hexagon head screw 22.
4.Block flange 23 with the flange wrench as delivered
together with the equipment.
5.Tighten screw 22 counter clockwise by means of the
tubular key as delivered together with the equipment.
6.Place guard 5 in its original protective position.
7.Revise the operation by carrying out a cutting operation
with no load.
10. Fixing for operation
Whenever possible, the workpiece must be fixed in such a
manner that the hand does not intervene.
During the cut, keep the workpiece fixed to the support.
ALL MACHINES ARE PREPARED FOR MOUNTING
CLAMPS ALLOWING FASTENING THE PROFILE IN A
SAFE MANNER.
To avoid deformations of the workpieces during fixing
thereof, the use of wooden profiles being easily applicable
to the movable jaws of the clamps is advised. Clamps can
be easily extracted and leave the working surface totally
clear.
For cutting long workpieces under safe conditions it is
essential to hold them with additional supports.
11. Limits regarding the workpiece size
Limits for all models as included in the present manual
SC250W
Kind of cut
90º
45º
45º Inclined
45º-45º Composed
Upper table
SC2500W
Kind of cut
90º
45º derecha
45º izquierda
45º inclinado
45º-45º Compuesto
0º recto
45º recto
Tubo PVC
Mesa superior
52
Limit of the workpiece size
in mm
140x75
90x75
130x52
70x50
0-40
Limit of the workpiece size
in mm
135x75 / 60x95
90x75 / 35x100
90x75 / 35x100
135x45 / 55x65
43x65 / 85x55
60x95
55x65
Ø 75
0-40