Hendi 860502 Manual Del Usuario página 8

Main parts of the product
GB
(Fig.1 on page 4)
1. Lid
2. Soup pot
3. Water pot
4. Housing
Control panel
(Fig.2 on page 4)
1. Operating indication lamp
2. ON/ OFF Switch
3. Malfunction indication lamp
4. Temperature display
5. Temperature control buttons
Preparation before use
• Remove all protective packaging and wrapping.
• Check to make sure the appliance is undamaged and with
all accessories. In case of incomplete delivery and damages.
Please contact supplier immediately. Do not use the appli-
ance.
• Clean the appliance before use (See == > Cleaning & Main-
tenance).
• Make sure the appliance is completely dry.
• Place the appliance on a horizontal, stable and heat resistant
surface that is safe against water splashes.
• Keep the packaging if you intend to store your appliance in
the future.
Operating instructions
(Control panel: Fig.2 on page 4)
1. Fill the water pan with water up to the MAX (min. up to the
MIN) mark.
2. Fill the soup pot with soup not over the MAX mark.
3. Connect the soup kettle to power and press the ON/OFF
switch (2).
4. Once the soup kettle is switched on. Its default SET TEM
PERATURE is at 80°C.
5. You can adjust the SET TEMPERATURE by pressing the UP
and DOWN buttons (5) at the left side of the control panel.
6. The soup kettle is in operation. Before the soup reaches the
SET TEMPERATURE, both the SET TEMPERATURE and the
ACTUAL TEMPERATURE will be alternately displayed.
Overheating Protection
• If the water level in the water pot is too low, the red indication
lamp (3) will blink and the buzzer sounds.
• You should fill the water pan with water no further than to the
MAX mark and switch off the soup kettle.
Then you need to wait for a while until the temperature of the
soup kettle has dropped before switching on the soup kettle
again.
If the red indication lamp is on, but no buzzer alarms
• This is a signal that something is wrong inside the soup kettle,
the user should bring the soup kettle for service.
NOTE: the thermostat is adjustable from 65°C to 95°C by 1°C
increments. (Topic)
8
Cleaning & maintenance
ATTENTION! Always disconnect the appliance from the elec-
trical mains and cool down before storage, cleaning & main-
tenance.
Do not use water jet or steam cleaner for cleaning and do not
push the appliance under the water as the parts will get wet
and electric shock might be resulted.
Cleaning
• Never immerse the appliance in water or other liquids.
• Never use abrasive sponges or detergents, steel wool or
metallic utensils to clean the interior or exterior parts of the
appliance.
• Dry all parts with a dry cloth before storing the appliance.
• If used intensively, regularly remove lime scale from the bot-
tom of the water tank.
• Avoid water contact with the electrical components as much
as possible.
• Never use aggressive cleaning agents, abrasives or chlorinat-
ed cleaners. Do not use any sharp or pointed objects. Do not
use petrol or solvents!
Descaling
• Hard water may cause some deposits to form inside the con-
tainer and cause possibly damage to the appliance.
• Thus, descale the appliance regularly. The descaling inter-
vals depend on water hardness and frequency of use. Use
only commercially available descaling agents and follow the
instructions of the manufacturer.
- Fill the container with water and appropriate amount of
descaling agent up to MAX level.
- Start boiling the solution.
- After boiling, dispose of the solution of water and descaling
agent properly.
• Rinse the container and boil twice to remove any residues.
Maintenance
• Check the operation of the appliance regularly to prevent
problems that can cause serious accidents.
• As soon as you feel the appliance isn't working correctly or
there is a problem, stop using the appliance, shut it off and
contact the supplier.
Storage
• Before storage, always make sure the appliance has already
been disconnected from the electrical outlet and cooled down
completely.
• Store the appliance in a cool, clean and dry place.
Troubleshooting
If the appliance does not function properly, please check the
below table for the solution. If you are still unable to solve the
problem, please contact the supplier/service provider.