Klein Tools 501-915 Manual De Instrucciones página 10

ENGLISH
Determining an Unknown VoP Value
Follow these instructions to set the Length Constant based on a sample cable
of known length. The Cable Length Meter can calculate a VoP from a test cable
length of 25 to 1000 ft. (10 to 300 m). Longer cable lengths will give more
accurate results. It is recommended to use at least 50' (20 m).
1. Prepare a length of the same type of cable for which you need to determine the VoP.
2. Determine the actual length of the test cable length using the markings on the
cable, a tape measure, laser distance meter, etc.
3. Connect the test cable length to the Cable Length Meter as described in
"MEASURING CABLES" section.
4. Press the Power button
5. Press the "More" button (two dots)
6. Use the Up
11
and press the "Select button" (three dots)
7. Press the "Select" button (three dots)
8. Press the "Edit" button (two dots)
buttons to select the cable type to be edited, and press the "Save" button
9. If testing data cable, use the Up
pair to be used for the test. Press the "Edit" button (two dots)
pairs, then press the Save button
cable types, skip this step.
10. Use the Up
11
the "Edit" button (two dots)
changed. Change the VoP percentage value by using the Up
dots) , and Right (one dot)
9
correct value. then press the Save button
11. Use the Up
11
selections. Press the "Edit" button (two dots)
to the new known VoP, then press the Save button
Toning Data Cable
1. Insert RJ45 cable into RJ45 Port
cable to be toned.
2. Press the Power button
3. Use the Up
11
4. Press the "Select" button (three dots)
5. Use the Up
11
button (three dots)
6. Toning will default to "OFF" for each of the pairs. Use the Up
buttons to select the desired pair(s) and press the "Edit" button (two dots)
scroll through OFF, 1200, 1000/1500Hz warble for each pair (multiple pairs can be
toned at the same time by selecting a tone frequency for each pair to be tested).
7. With toning turned on, use the Up
1200Hz or 1000/1500 Hz warble for each pair (multiple pairs can have tone enabled
simultaneously; select desired tone frequency as described above).
Toning Coax and Other Cable
1. Press the Power button
2. Use the Up
11
3. Press the "Select" button (three dots)
4. Use the Up
11
the "Select" button (three dots)
5. Toning will default to "OFF". Press the "Edit" button (two dots)
OFF, 1200Hz or 1000/1500 Hz warble.
10
OPERATING INSTRUCTIONS
to power-ON the meter. 5
and Down Arrow buttons to highlight "Calibrate VoP/Length"
12
and Down Arrow buttons to select the VoP percentage value. Press
12
and the first digit will blink, indicating that is able to be
7
7
and Down Arrow buttons to select the Name and Manufacturer
12
to power-ON the meter.
5
and Down Arrow buttons to select "Tone".
12
and Down Arrow buttons to select "Data" and press the "Select"
12
.
8
to power-ON the meter.
5
and Down Arrow buttons to select "Tone".
12
and Down Arrow buttons to select "Coaxial" or "Other", and press
12
8
.
7
.
8
.
8
and use the Up
7
and Down
11 12
to complete the change. NOTE: For all other
10
Arrow buttons until the value for the Length is the
to complete the change.
10
to create a name and assign a manufacturer
7
to complete the change.
10
or use Alligator Clips
2
.
8
and Down
11 12
.
8
.
and Down
11 12
Arrow buttons to select the wire
to change the pin
7
, Down
11
to connect to wires in
13
and Down
11
Arrow buttons to select
to scroll through
7
Arrow
.
10
, Left (three
12
Arrow
12
to
7