Solución De Fallos; Troubleshooting,Cleaning - Rotoclear P-11500 Manual De Instrucciones

Mirilla rotativa
Tabla de contenido
10
Solución de fallos
En el caso de fallos proceda de la siguiente forma:
La instalación eléctrica debe ser realizada
exclusivamente por personal técnico capacitado y
autorizado.
10.1
La placa rotativa no gira.
La placa rotativa no gira y emite tonos alternantes.
El rotor está bloqueado mecánicamente.
Desconecte el sistema de la tensión eléctrica.
Compruebe manualmente la rotación libre girando
el rotor con la mano.
El uso de agua cruda puede formar una costra en
la grieta del lado interior del rotor. Eliminar los
depósitos con un cuchillo o un rascador libre de
residuos.
Posiblemente se encuentren suciedad o virutas en
la separación entre el estator y el rotor.
Limpie la zona alrededor de los campos
magnéticos. En caso necesario utilice un imán
adherente fuerte de oficina.
Mientras tanto no apoye la placa sobre un banco de
trabajo sucio; puede utilizar un cartón limpio como
base.
Si se acumulan muchas virutas y se repiten los
fallos por suciedad le recomendamos que aumente
la presión interior.
Aumente la presión de alimentación en 0,5 bar y
compruébela en el centro del equipo. Vuelva a
montar la placa rotativa. Compruebe el movimiento
mecánico libre con la mano y conecte el equipo.
10.2
La placa rotativa se detiene y se vuelve a poner
en movimiento poco tiempo después.
El motor tiene una función de protección integrada.
Si el motor experimenta una gran carga y se
calienta, entonces la seguridad contra sobrecarga
lo desconecta y lo vuelve a conectar después de un
breve periodo de tiempo.
Desconecte el sistema de la tensión eléctrica.
Evite que el chorro de refrigerante apunte
directamente hacia la placa rotativa. Compruebe si
la placa rotativa roza con algún objeto.
Compruebe si el centro se calienta excesivamente.
10.3
La placa rotativa no gira.
La placa rotativa puede girarse a mano 360º y tras
impulsarla gira libremente.
Compruebe si la tensión tiene la polaridad correcta
y en caso necesario cambie la posición de los
cables.
Compruebe si cuenta con la tensión correcta y si el
suministro eléctrico es suficiente.
En la figura pto. 5 está representada la polaridad.
Rotoclear está protegido internamente contra una
polaridad incorrecta, así como contra sobre y
subtensión. Se trata de un motor electrónico. La
medición de la resistencia interna no permite sacar
conclusiones sobre el funcionamiento del motor.
Troubleshooting
Proceed as follows when malfunctions occur:
Electrical installation work is only permitted to
be done by trained electricians.
The rotating window does not rotate.
The rotating window does not rotate and
produces variable sounds. The rotor is
mechanically blocked.
Verify that the electrical power is off. Check the
free rotation of the rotor by hand.
When using hard water may be in the gap
area, a crust forming on the inside of the rotor.
Eliminate the cake with a
knife or a scraper residue-free.
Dirt or chips may be embedded in the gap
between the stator and rotor.
Clean the area surrounding the magnetic
fields.
You may try using an ordinary magnetic clamp
from your office.
Do not place the rotor on a dirty workbench,
but use a clean cardboard surface instead.
If there is significant chip exposure and the
system malfunctions repeatedly, we
recommend increasing the internal pressure.
Increase the feed pressure by max. 0.5 bar
and check the velocity pressure in the
connecting box. Reinstall the rotating window.
Verify the mechanical free rotation of the rotor
by hand. Switch on the power.
The rotor stops rotating and resumes
rotation after a short period.
The motor has an internal safety function. If
the motor overheats because of a heavy load,
the overload function cuts power and switches
back on after a short period of time.
Make sure that the electrical power is off.
Do not point the coolant directly at the rotating
window. Check if the rotating window runs
smoothly or if it rubs against something.
Mind overheating in the center.
The rotating window does not rotate.
The rotating window is mechanically free,
rotates by 360° when moved manually, and
spins freely when initiated by hand.
Check the right polarity of the system and
swap the wires when needed.
Check the right voltage and if the power supply
is sufficient to start the system.
For more information as to correct connection
and polarity, see fig. 5.1.
Rotoclear is internally protected against wrong
polarity and low or high voltage. It is not
possible to check the function of the motor by
measuring its impedance.
16
Tabla de contenido
loading

Tabla de contenido