Idiomas disponibles
Idiomas disponibles
Emission values for vibration
Vibration
Classification according to per-
formance class
STARLOCK
STARLOCK PLUS
a
K
* These values are based on a no-load measurement with max-
imum speed stage (6). In each case, the application tool corre-
sponds to the highest mass inertia of its performance class.
Operating Instructions.
Do not use accessories not specifically intended and
recommended for this power tool by FEIN. The use of
non-original FEIN accessories can lead to overheating
of the power tool and destroy it.
Changing the tool (see pages 6/7).
Do not switch the power tool on while the clamp-
ing lever is open. Otherwise there is danger of
crushes or contusions to the hand and fingers.
Do not reach into the area of the clamping jaws.
Otherwise there is danger of crushes or contu-
sions to the fingers.
Charge-control Indicator on the Battery
(see page 8).
The charge condition can be indicated by the green
LEDs of the charge-control indicator on the battery.
Press the charge-control indicator button
to indicate the charge condition.
When no LED lights up after pressing the charge-con-
trol indicator button, the battery is defective and must
be replaced.
Additional operating instructions.
Do not actuate the clamping lever while the power
tool is running. Otherwise there is danger of
injury.
Do not operate the power tool with with open
clamping jaws and without an application tool!
This could damage the power tool.
When the clamping jaws are open before the
application tool is inserted, pivot the clamping
lever toward the front and then back again. The
clamping jaws are closed now. The application
tool can be inserted.
Guide the power tool toward the work piece only
when switched on.
The application tool can be offset in 30° steps and fas-
tened in the most favourable working position.
The self-start prevention lock prevents the power tool
from automatically starting when the battery is inserted
while the on/off switch is set to on.
If the power tool shuts off without the switch being
actuated, switch the power tool switch off, remove the
battery and reattach it.
Notes on sanding.
Press the power tool with the sanding sheet briefly and
firmly against a flat surface and briefly switch the power
tool on. This provides for good adhesion and prevents
Weighted
premature wear.
acceleration*
When only one tip or corner of the sanding sheet is
2
3.6 m/s
worn, it can be removed again and reattached turned by
2
120°.
7.0 m/s
Work with the entire surface of the sanding plate, not
2
1.5 m/s
only with the tip.
When sanding with small triangle sanding plates, select
a high oscillating frequency (electronics level 4 – 6);
when sanding with the round sanding plate and the
large triangle sanding plate, select a moderate oscillating
frequency (max. electronics level 4).
Sand with continuous motion applying moderate pres-
sure. Applying excessive pressure does not increase the
rate of removal, it only wears off the sanding sheet
faster.
Notes on sawing.
Select a high oscillating frequency. Round saw blades
can be released and clamped offset again, to allow for
uniform wearing off.
Notes on scraping.
Select a moderate to high oscillating frequency.
Transport.
The contained Li-ion batteries are subject to the Dan-
gerous Goods Legislation requirements. The user can
transport the battery packs by road without further
requirements.
or
When being transported by third parties (e.g.: air trans-
port or forwarding agency), special requirements on
packaging and labelling must be observed. For prepara-
tion of the item being shipped, consulting an expert for
hazardous material is required.
The recommended Li-ion batteries are subject to the
Dangerous Goods Legislation requirements. The user
can transport the batteries by road without further
requirements.
When being transported by third parties (e.g.: air trans-
port or forwarding agency), special requirements on
packaging and labelling must be observed. For prepara-
tion of the item being shipped, consulting an expert for
hazardous material is required.
Dispatch batteries only when the housing is undam-
aged. Tape or mask off open contacts and pack up the
battery in such a manner that it cannot move around in
the packaging. Please also observe possibly more
detailed national regulations.
Repair and customer service.
electricians, as improper maintenance can result in con-
siderable hazards for the user.
Please observe that power tools may only be
repaired, maintained and inspected by qualified
en
19
