Kenmore PG-40409S0LB-COSG Manual De Uso Y Cuidado página 9

WARNING
Turn controls and gas source or tank OFF when
not in use.
CAUTION
If ignition does NOT occur in 5 seconds, turn the burner
controls OFF, wait 5 minutes and repeat the lighting
procedure. If the burner does not ignite with the valve
open, gas will continue to flow out of the burner and
could accidently ignite with risk of injury.
Match Lighting Instructions
▲
Do not lean over grill while lighting.
1. Open lid during lighting.
2. Place match into match holder (hanging on left side
panel).
3. Light match and insert match holder through lighting hole
in left side of firebox. Align lit match with first burner on
left.
4. Turn knob of first left burner to HI position. Be sure
burner lights and stays lit. Withdraw match holder from
firebox and extinguish match.
5. To light the other burners, turn each knob in succession
to HI.
6. Once burners are lit, adjust knobs to desired flame
setting. To extinguish an individual burner, turn its knob to
OFF.
Searing Burner Match Lighting
1. Open searing burner lid. Turn on gas at LP cylinder.
2. Place lit match near burner.
3. Turn searing burner knob to HI. Be sure burner lights and
stays lit.
Burner Flame Check
• Remove cooking grates and heat diffusers. Light burners, turn
knobs from HI to LO. You should see a smaller flame in LO
position than seen on HI. Perform burner flame check on searing
burner, also. Always check flame prior to each use. If only low
flame is seen refer to "Sudden flame drop or low flame" in the
Troubleshooting Section.
Turning Grill Off
• Turn all knobs to OFF position. Turn LP cylinder off. When you
are finished grilling, raise the grill lid while allowing the grill to
fully cool. If the grill lid is closed during grill cooling,
condensation may occur on interior grill surfaces and possibly
cause them to rust.
Igniter Check
• Turn gas off at LP cylinder. Press and hold electronic igniter
button. "Click" should be heard and spark seen each time
between collector box or burner and electrode. See
"Troubleshooting" if no click or spark.
Valve Check
• Important: Make sure gas is off at LP cylinder before checking
valves. Knobs lock in OFF position. To check valves, first push in
knobs and release, knobs should spring back. If knobs do not
spring back, replace valve assembly before using grill. Turn
knobs to LOW position then turn back to OFF position. Valves
should turn smoothly.
Hose Check
• Before each use, check to see if hoses are cut or worn. Replace
damaged hoses before using grill. Use only
valve/hose/regulator as specified in the parts list of this Use &
Care Guide.
Cast Iron Grate Seasoning (if applicable)
First Use –Before first use, season cast iron grates as follows:
Rinse cast iron grates with hot water. Do not use soap. Dry grates
thoroughly with a cloth towel. Coat grates with vegetable oil or
nonstick cooking spray. Place grates in grill. Start grill and slowly
raise temperature to 350° - 400° F. Heat grates for one hour. Turn
off grill and allow grates to cool completely before using to cook.
Cleaning – Do not use soap when cleaning grates. Clean grates with
a stiff brush and hot water. Dry grates thoroughly with a cloth towel.
Re-seasoning – Re-season grates when rust spots appear on grate
surface. When re-seasoning grates, soap may be used with hot
water to clean grates. After cleaning, dry grates thoroughly with a
cloth towel. Coat grates with vegetable oil or non-stick cooking
spray. Place grates in grill. Start grill and slowly raise temperature to
350° - 400° F. Heat grates for one hour. Turn off grill and allow
grates to cool completely before using again.
General Grill Cleaning
• Do not mistake brown or black accumulation of grease and
smoke for paint. Interiors of gas grills are not painted at the
factory (and should never be painted). Apply a strong solution
of detergent and water or use a grill cleaner with scrub brush
on insides of grill lid and bottom. Rinse and allow to completely
air dry. Do not apply a caustic grill/oven cleaner to painted
surfaces.
• Porcelain surfaces: Because of glass-like composition, most
residue can be wiped away with baking soda/water solution or
specially formulated cleaner. Use nonabrasive scouring
powder for stubborn stains.
9