Stanley SCD700 Manual Del Usuario página 25

Note: When moving from forward to reverse, or vice versa,
always release the trigger switch
Drilling
● Use sharp drill bits only.
● Support and secure work properly, as instructed in the
Safety Instructions.
● Use appropriate and required safety equipment, as
instructed in the Safety Instructions.
● Secure and maintain work area, as instructed in the Safety
Instructions.
● Run the drill very slowly, using light pressure, until the hole
is started enough to keep the drill bit from slipping out of it.
● Apply pressure in a straight line with the bit. Use enough
pressure to keep the bit biting but not so much as to stall
●
handle, and the other gripping the bottom around the
battery area or the auxiliary handle if provided.
● DO NOT CLICK THE TRIGGER OF A STALLED DRILL
OFF AND ON IN AN ATTEMPT TO START IT. DAMAGE
TO THE DRILL CAN RESULT.
● Minimize stalling on breakthrough by reducing pressure
and slowly drilling through the last part of the hole.
● Keep the motor running while pulling the bit out of a drilled
hole. This will help reduce jamming.
● Make sure switch turns drill on and off.
Drilling in wood
Holes in wood can be made with the same twist drill bits used
for metal or with spade bits. These bits should be sharp and
should be pulled out frequently when drilling to clear chips
from the
Drilling in metal
Use a cutting lubricant when drilling metals.
The exceptions are cast iron and brass which should be drilled
dry. The cutting lubricants that work best are sulphurized
cutting oil.
LED work light (Fig H)
When drill is activated by pulling the trigger switch (1), the
integrated LED work light (8) will automatically illuminate the
work area.
Note: The work light is for lighting the immediate work surface
and is not intended to be used as a
Troubleshooting
Problem Possible cause
Unit will not start. Battery pack not
installed properly.
Battery pack
not charged.
Unit starts immediately The switch has been
upon inserting battery left in the "on" position.
bit.
Possible solution
Check battery
pack installation.
Check battery pack charging
requirements.
The switch must be moved
to "off" to prevent the tool
from immediately starting
when battery is inserted.
(Original instructions)
Problem Possible cause
Battery pack will Battery pack not
not charge. inserted into charger.
Charger not plugged in. Plug charger into a working
Surrounding air
temperature too hot or
too cold.
Unit shuts off abruptly. Battery pack has
reached its maximum
thermal limit.
Out of charge. (To
maximize the life of
the battery pack it is
designed to shutoff
abruptly when the
charge is depleted.
Maintenance
Your STANLEY tool has been designed to operate over a long
period of time with a minimum of maintenance. Continuous
satisfactory operation depends upon proper tool care and
regular cleaning.
Your charger does not require any maintenance apart from
@
regular cleaning.
Warning! Before performing any maintenance on
the tool, remove the battery from the tool. Unplug the
charger before cleaning it.
● Regularly clean the ventilation slots in your tool and
charger using a soft brush or dry cloth.
● Regularly clean the motor housing using a damp cloth.
● Do not use any abrasive or solvent-based cleaner.
Protecting the environment
Separate collection. Products and batteries marked
with this symbol must not be disposed of with
normal household waste.
Products and batteries contain materials that can be
recovered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according
to local provisions. Further information is available at
www.2helpU.com.
Technical data
Voltage
No-load speed
Max. torque
Chuck capacity
Torque setting
Max Drilling capacity
Steel/wood
Weight
ENGLISH
Possible solution
Insert battery pack into
charger until LED lights.
outlet.
Move charger and battery
pack to a surrounding air
temperature of above 45º C
or below +40.5º C.
Allow battery pack to cool
down.
Place on charger and allow
to charge.
SCD700
18V
V
(20V MAX) (20V MAX)
DC
Min 0-400/0-1500 0-400/0-1500
-1
Nm 50
mm 13
Position 23
mm 13/35
kg 1.2
SCD708
18V
52
13
23
13/35
1.2
25