Edesa EVT-6328 B Manual De Instrucciones página 13

Idiomas disponibles

Idiomas disponibles

· When the control is switched on, the ON/OFF button
has priority over all other button and, therefore, the
control can be switched off at any time, even when
several buttons are pressed at the same time or a
button is kept held down.
· In standby mode, no effect will be caused by but-
tons being kept held down. However, before the
electronic control can be switched back on, it has to
detect that no button is pressed down.
Button lock (child safety feature)
• Child safety feature:
Button lock:
To activate the child safety device after turning on the
Touch Control, press and hold the MINUS (2) button.
Then press the button twice to select the cooking
zone:
· upper left > if the hob has 3 cooking zones
· lower left > if the hob has 4 cooking zones
An "L" standing for LOCKED (child safety feature pre-
venting unintended switch on) will be indicated on all
displays. If a cooking zone is in "hot" mode, "L" and
"H" will be alternately displayed.
This operation must take place within a 10 successive
seconds and no button other than those described
must be pressed. Otherwise, the sequence will be
interrupted and the hob will not be locked.
The electronic control remains locked until it unlocked
by the user, even if it has been switched off and back
on meanwhile. Not even touch control resetting (after
a voltage drop) will interrupt the button lock.
Cancelling the button lock:
After switching the touch control on, the child
safety feature can be disabled. Follow the same
procedure as for locking: press and hold the
MINUS (2) button, then press the button twice to
select the cooking zone:
· upper left > if the hob has 3 cooking zones
· lower left > if the hob has 4 cooking zones
If all operations are carried out in the right order
within 10 seconds, the button lock will be cancelled
and the touch control switched off. Otherwise, the se-
quence will be considered incomplete and the touch
control will remain locked and will switch off after 20
seconds.
Switch the touch control back on using the ON/OFF
button and all displays will be indicate "0", the de-
cimal points will flash and the touch control will be
ready for cooking. If a cooking zone is in "hot" mode,
"0" and "H" will be alternately displayed.
Control of multiple circuits
When a dual / triple cooking zone is activated, the 3
circuits are switched on at the same time. The activa-
tion / deactivation of each circuit is done with button
4 and it is indicated with an illuminated segment (8).
Sound signal (buzzer)
The following activities are indicated by a buzzer du-
ring use:
· Normal button pressing by a short sound.
· Buttons kept pressed down for more than 10 sec. by
a long, intermittent sound.
Maintenance (Fig. 4)
By means of a scraper immediately remove any allu-
minium foil bits, food spills, grease splashes, sugar
marks and other high sugarcontent food from the
surface in order to avoid
damaging the hob.
Subsequently clean the surface with some towel and
appropriate product, rinse with water and dry by
means of a clean cloth. Under no circumstance
should sponges or abrasive cloths be used; also
avoid using aggressive chemical detergents such as
oven sprays and spot removers.
Installer's Instructions
Installation
These Instructions are for the qualified technician, as
a guide to installation, adjustment and maintenance,
according to the laws and standards in force. The-
se operations must always be carried out when the
appliance has been disconnected from the electric
system.
Positioning (Fig. 5)
1 Front view
2 Front side
The appliance can be fitted into a working area as
illustrated on the figure. Apply the seal supplied over
the whole perimeter of the working area.
Electrical connection
Prior to carrying out the electrical connection, please
ensure that: the plant charac- teristics are such as to
follow what is indicated on the matrix plate placed at
the bottom of the working area;
- that the plant is fitted with an efficient earth
connection, following the standards and law
provisions in force.
- The earth connection is compulsory in terms of
the law.
Should there be no cable and/or plug on the equip-
ment, use suitable absorption material for the wor-
king temperature as well, as indicated on the matrix
plate. Under no circumstance must the cable reach
a temperature above 50°C of the ambient tempera-
ture.
loading

Este manual también es adecuado para:

Evt-6328 x