Idiomas disponibles
Idiomas disponibles
displays and LEDs switch off and the touch control is
in standby mode.
Press the ON/OFF (1) button to switch the touch con-
trol on.
The cooking zone displays indicate "0". If a cooking
zone is in "hot" (high temperature) mode, the display
will alternately indicate "H" and "0".
After switching the touch control on, it will remain ac-
tive for 20 seconds. If no cooking zone is selected, the
touch control automatically switches back to standby
mode.
The touch control can only be switched on by pres-
sing the ON/OFF (1) button.
Pressing the ON/OFF (1) button at the same time as
other buttons will have no effect and the touch con-
trol will remain on standby.
The touch control can be switched off at any time
using the ON/OFF (1) button. This is even the case
when the control has been locked by the child safety
feature.
The ON/OFF (1) button always takes priority in the
switching off function.
Automatic off
Once switched on, the touch control automatically
switches off after 20 seconds of inactivity. After selec-
ting a cooking zone, the automatic off time is divided
into 10 seconds, after which the zone is deselected
and, after another 10 seconds, the touch control swit-
ches off.
Switching a cooking zone on/off
If the touch control is switched on, the cooking zone
can be selected by pressing the button (5) of the co-
rresponding zone.
The display (6) of the zone selected lights up, while
the remaining displays are dimmed. if the cooking
zone is "hot", "H" and "0" are alternately displayed.
Press the PLUS (3) or MINUS (2) button to select a set-
ting and the zone will begin to heat up.
Once the cooking zone has been selected, the setting
can be selected by keeping the PLUS (3) button pres-
sed down. The setting begins at level 1 and increases
by 1 level every 0.4 seconds. When setting "9" is rea-
ched, the setting will not be changed further.
If the setting level has been selected using the MINUS
(2) button, the start level is "9" (maximum level). Keep
the button pressed down to lower the active level by 1
every 0.4 seconds. When setting "0" is reached, there
will be no further setting changed. The setting can
only be changed by pressing the MINUS (2) or PLUS
(3) button again.
Switching a cooking zone off
Select the zone to be switched off using the corres-
ponding button (5). The display (6) of the zone se-
lected lights up, while the remaining displays are
dimmed. Press the PLUS (3) and MINUS (2) buttons
at the same time and the setting level of the zone is
changed to 0. Alternatively, the MINUS button (2) can
be used to reduce the setting level to 0.
If a cooking zone is "hot", "H" and "0" will be alter-
nately displayed.
Switching all cooking zones off
Press the ON/OFF (1) button to immediately switch
off all zones at any time. In standby mode, an "H"
is displayed in all cooking zones that are "hot". The
remaining displays will be switched off.
Setting level
The cooking zone can be set to 9 levels that are in-
dicated by the numbers "1" to "9" on the seven-seg-
ment LED displays (6).
Residual heat indicator
This informs the user that the glass is at a dange-
rous temperature in the event of touching the area
located around the cooking zone. The temperature is
determined by a mathematical model and any resi-
dual heat is indicated by a "H" on the corresponding
7-segment display.
Heating and cooling are calculated based on:
· The selected setting level (between "0" and "9")
· The ON/OFF time.
After switching off the cooking zone, the correspon-
ding display will indicate "H" until the temperature
in the zone has dropped below the critical level (≤
60°C).
Automatic off function (operating time limitation)
(Fig.7)
In terms of the setting level, if no operation occurs
each cooking zone switches off after an established
maximum time.
Each operation in the cooking zone condition (using
the PLUS (3) and MINUS (2) or dual zone) restarts the
maximum operating time of the zone by resetting it
to its initial value.
Protection against unintended switching on
· If the electronic control detects a button being held
down for approx. 10 sec. it will switch off automati-
cally. The control sends out an audible error signal
to warn the user that the sensors have detected the
presence of an object. The displays indicate error
code " E R 0 3 ". If the cooking zone is in "hot" mode,
"H" will be indicated alternately on the display with
the error signal.
· If no cooking zone is activated within 20 seconds
after switching on the touch control, it will return to
standby mode.
